• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

How bendable are GS650G stock exhaust pipes?

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
I just got a 1981 GS650G, which I am in the process of getting running.

This site has been a great resource, and most of the questions I had were already answered in other posts. I didn't find anything on this, though.

The bike's original owner had a windjammer and a big trunk on it. It looks like he may have had saddlebags, too, as he welded 3 inch extensions onto the exhaust brackets and bent the mufflers down so instead of curving up they go straight back. It looks like he made the bend to bring the mufflers closer to the rear wheel to retain some cornering clearance, but the mufflers will still be the first thing to touch down. The bend occurs in the header pipes right before the muffler.

When I look at the bottom of the pipes where they are bent, there is a bulge on the bottom of the pipe where the bend occurred. It is in the same place on both pipes.

I'd like to have more cornering clearance, but I don't want to break the pipes by bending them back. Also, I want to keep the bike stock, so I don't want to switch to a different exhaust system.

Any Ideas on how best to do this? I'm thinking maybe heat it up and pull up on it as hard as I can.

Thanks.
 
I would cut the bend off and get that small section replaced, if you heat the pipe up you run the risk of cracking it, under no circumstances pull on a heated pipe as it will definitely crack
 
Good advice.

In thinking about my options, I've decided to leave it alone and see how it corners. I don't know if the pipes are rusty inside, or how brittle the metal is. I'm reasonably sure that if I mess with it, it will be a can of worms.

It's just a really wierd thing to see done to a bike, so I didn't notice it when I bought it. I think the original owner was some kind of mad hobbyist.

On the plus side, if I want to bolt giant saddlebags on it and ride it around the world, there's room.
 
If you want to put the pipes back right, you better just go get a set of used ones, or new ones if you can afford it.

Now, how to best bend pipes. You will not break them if you heat them and bend them. That is the correct way to bend steel tubing. Your chome will peel off, and you will probably collapse them if you try to bend without a mandrel, too.

If you decide to bend up a custom set of headers in one piece, the trick is to completely fill the pipe with extremely fine DRY sand and weld the ends off, either with caps or just pinched shut. You can then heat and bend to your heart's content, as long as you don't stretch things so far that the thinning section breaks. You can then empty the sand out, have said pipes polished, and chromed. Be careful where you dump that sand, it's REALLY hot.

Steel, unless it is already rusted to pieces will not break when heated and bent. Aluminum goes "hot short" and gets brittle if heated and bent. It will just crumble if heated to a dull red and bent, that's what makes it so tricky to weld and cast correctly. Any residual stresses will break the weld or casting before it cools to its full strength (yeah, I play with that stuff, too).
 
You must log in or register to reply here.
Back
Top