• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Mixture screw threads trashed

  • Thread starter Thread starter t3rmin
  • Start date Start date
T

t3rmin

Guest
I've discovered the threads on my #3 carb's mixture screw (the one with the needle-like point) are trashed. Dunno what the PO did but it screws in/out *really* hard and visually the threads are flattened.

Any ideas on how to best resolve this? My thoughts so far involve finding a screw at the hardware store with the same threads and running it into the carb to try to clean up the threads inside, then finding a nut that fits the screw and running it through to clean up its threads. The threads are awful fine so hopefully I can locate a screw and nut that match.

If I can't recover this screw, does anyone know where I can buy them or does anyone have an extra one around? I'm also missing two washers and one spring from the other mixture screws and haven't had any luck finding replacements either. None of the microfiches list these parts since I guess the mixture screw adjustment was set at the factory and not considered user serviceable...
 
The screws, washer, spring and o-ring come in the carb rebuild kits. You may be able to find the washers and o-rings separately. I think I have a spare screw from a rebuild kit I never used (PM me). You may be able to find a similarly threaded long steel screw and tap it out but, IMHO, your best bet may be to find someone parting out a rack of carbs from a similar bike (some models share carb bodies and you can just replace the jets). I had a similar thing happen to me with my #2 on the 550. Even when I managed to tap out the threads using a similarly sized steel screw, the carb wouldn't work right (I couldn't set the idle mix properly on it). I eventually found a #2 on this web site and its been working great since.
 
Well that is the same carb off of which I broke a float post (but fixed rather nicely with JB weld), so it wouldn't be a bad idea to replace it. But as usual I'm trying to get by on the cheap. From a practical standpoint, I don't see why I can't make this carb work if I can fix the mixture screw, provided I can get all the metal shavings cleaned out from the cross-threading.

Actually I have seen the screws in rebuild kits, but as I'd already ordered a full o-ring set and bowl gaskets separately, I didn't particularly want to shell out for the kit just for the screw. I'll PM you about that screw, since the head on this one is starting to look questionable anyway and I'd hate to get it stuck.
 
Help! Can't find a tap screw!

Help! Can't find a tap screw!

Well I've been to the hardware store and they don't have anything with the right threads to tap out that socket. Anyone have any idea what the thread pitch is on those screws (it's an M6 diameter) and where I can find (online or otherwise) something to tap out the hole?:cry:
 
If it was me, I'd post it on here and look for a carb body. I found one through an excellent member here and I'd be willing to bet you may too. The passages that feed that pilot fuel screw have extremely small holes and I think you're just asking for trouble.
My 2 cents.
 
I'm sure you're absolutely right and that's probably very good advice... ;-)

I'm going to have one more go at it, though. After MUCH searching I did manage to find a an M6-0.50mm tap (ordered an M6-0.75mm too, just in case my measurement was off) at jlindustrial.com and DimitriT has graciously offered a spare mixture screw.
 
are you talking about the air screw that is on the bottom of the bowls and is exposed and facotory set? if so I talked with a mukuni dealer and he said that those parts are hard too find oem since we are not suppose too touch those. I had the same exact thing happen too my gs 750 (well my sons). The guy turned em in so hard he broke a piece of brass off inside the carb body. I took a fine wire brush filament and used that too poke it thru then shot air thru them after using pb blaser on it for two nights. It did work free and shot right out.
But I had a problem with the rubber washer. sealing up the gas. I asked the mukuni dealer if he had any and he said they don't usally carry that part. So I said what if I grind down the screw too a point again, turn it in the recommended amount of turns set by the factory and then iron/ jbweld them permantly shut? He said too do it. since once they are set the right amount they should never be bothered with again. So I did it like he recommneded or allowed. Today the bike has not dripped any gas, she runs on all four cyclinders and it will go anywhere.
So maybe this fix will help you out. dont know, you can only try.
 
Cyg said:
are you talking about the air screw that is on the bottom of the bowls and is exposed and facotory set?
Click to expand...

I think that's how it's set up on older carbs. On mine the only external adjustment besides the throttle is these screws. They're called the mixture screws and they're on the top, toward the motor side. I think they are factory set, though, and not considered user serviceable. I assume that's why none of the microfiches ever list 'em.

Fortunately none of the tips are broken off so I won't have to deal with that particular issue! I assume once I get them set correctly they won't have to be touched again. Unfortunately, I don't think there's a 'factory setting' number of turns to be found anywhere (since manuals ignore them altogether) so they'll have to be dialed in manually.
 
Hey, t3rmin (if you are still around). I'm having the same issue with my mixture screw threads. Did either of those taps work? Which one was the correct size? Thanks!
 
You must log in or register to reply here.
Back
Top