• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

running on two cylinders

  • Thread starter Thread starter rippledub@gmail.com
  • Start date Start date
R

rippledub@gmail.com

Guest
1980 GS1000G
Hey everyone, I am out on an early season ride in Colorado. Yesterday while I was riding I lost power, but not all power. When I stopped I checked my exhaust pipes, and 1 and 4 were barely warm, 2 and 3 were hot as they should be. So I am running on two cylinders only. Can I assume that the problem is the ignition coil, or are there other possibilities for 1 and 4 to go out at the same time? The bike still runs and starts, I was able to limp on to my destination, but it was using a lot of fuel.

Since I am on the road I don't have my books with me, so I have a few questions:

If it is the coil, does anyone know the ohm resistance for these coils?
Can you recommend a certain aftermarket, or is it important to go oem?
Should I replace both coils while I am at it?

Thanks in advance for any and all help!
Mark
 
Primary should be in the 3 - 5 Ohm range and the secondary 10 k ohm or more. Compare both coils they should be the same.
Coils are fairly bullet proof. I'd say it's more likely you have a supply problem to that coil. Plug under the tank is a usual suspect.
 
Have you checked for spark on 1&4? My thoughts are burned points if its a points system or coil went out personally I'd replace both at one time .
 
Good point also check for voltage to the coil before you condem it
 
Step one is to check voltage to the 1&4 coil... if the pipes appear to be just warm, those cylinders are not firing and the warmth is picked up from 2&3.

if voltage, then the coil is likely dead. If no voltage, keep in mind that the voltage going to 2&3 is just one leg off a split so the problem of no voltage will be the connector under the tank or the orange/green connected to the coil has come off or is loose. If there is power:

Step two is to check the 1&4 coil by swapping with the 2&3.

If the problem moves to the 2&3 cylinders and 1&4 now fire, then the coil that was originally on 1&4 is bad and needs to be replaced. If the problem remains, your IC electronic ignition wire for 1&4 may have come loose, the IC igniter connection to that wire may be loose, the Ic Igniter may be back or perhaps the 1&4 side pickup coil is bad. Try and fix any loose connection but if the connections are good, the ignition should be replaced (think Dyna S).
 
Thanks for all the suggestions!
I'm no pro with the meter, but I think I can figure out the basics here.

One Question, If both the 1 and 2 stopped firing at the same time can that be the points? Wouldn't one go out at a time? I remembered from rewiring my coils that each one handled two plugs, that's why I assumed coil. What don't I know about the points? (many things!!)

Ill get a meter and start checking things . . . thanks again, and I will post again if I run up on any other questions!

Mark
 
If your running on a points system like mine the top set controls the #1&4 & the bottom set controls #2&3 but I'd only mess with them only after you have ruled out the voltage at the coil the points ground out the coils completing the circuit thus building voltage in the primary winding of your coil once they open they break connection causing the voltage to run through the secondary winding I forgot what the term is called off hand but suffice it to say the voltage increases exponentially and fires the plug.
 
Turns out it was a broken wire at one of the solder points on the coil.

Thanks for your help everyone!

back on the road.

mark
 
Good day - New to this forum and have been reading - Working on a 82 GS1100GL - Started with helping a young fellow at work and turned into a obsession to get it running correctly - Was setting for 12 years and he bought it from his uncle - cleaned carbs and got running, was blowing main fuse and found and replaced bad rectifier - I can get it running but 1 and 4 are for the most part dead - can get a bit of life by covering air passage in carbs. due to the problem cylinder are on the same coil pack would like to check/swap before going through the carbs again - spark does look good w/ a in line tester installed on dead cylinders - My question is when you say " check the 1&4 coil by swapping with the 2&3 " I did swap 1 to 4 coil pac to 2 to 3 cylinder - no start at all ----are you talking just the wires going to plugs or do I also need to swap wires going to coil pac - Thank you Ron
 
Probably would be better to have your own thread on this new to you problem.

You need to swap the wires supplying electricity to the coils.
 
You must log in or register to reply here.
Back
Top