• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Scratched cylinder

  • Thread starter Thread starter Guest
  • Start date Start date
G

Guest

Guest
Recently acquired some GS850 cylinders & pistons to upgrade my GS750 (and a rebuilt bottom end that I have no need for). They were already re-honed with new rings, however one cylinder has a scratch in it deep enough to catch my fingernail.

In the photo, the bottom of the calliper is at 60 mm - approximately the lowest point where I reckon the top ring would be. So a good 20mm of scratch/gouge exposed to combustion.

Since I'm planning to replace my current cylinders for excess oil consumption and they have a couple of scratches in each of them, am I going to have similar problems with this? Should I rebore my 750 cylinders and get them perfect?
 
It'll probably smoke. If you want to use that cylinder try to find .05mm or 1mm oversized pistons and rings and get the cylinders cut or find another cylinder.
OR
Slap it together and ride it and hope it's not a fog machine.
 
he he - I like the cavalier attitude and would usually go for it but if she keeps smokin after tearing it down a second time (did head gasket and valve seals last year - that's when I saw the current scratches) I'm gonna be ****ed off.
 
I have built car engines with way worse, no smoke.
Even assembled a few with no where near the correct piston-cylinder fit, something like three times the spec. Worked fine. Ran a long time. Don't know how long it lasted but I ran the heck out of it for years.
I really wouldn't worry about that little scratch.

If it smokes after a good hard moto man style break in I will really be surprised.
 
tkent02 said:
I have built car engines with way worse, no smoke.
Even assembled a few with no where near the correct piston-cylinder fit, something like three times the spec. Worked fine. Ran a long time. Don't know how long it lasted but I ran the heck out of it for years.
I really wouldn't worry about that little scratch.

If it smokes after a good hard moto man style break in I will really be surprised.
Click to expand...

Cool thanks. I have little experience in this area and am after opinions of people who have been there before.

I want a well operating bike (which it is other than this little oil discrepancy...) but obviously don't want to chuck away money for nothing.
 
Who honed it?
Not much of a cross hatch pattern, at least not in the pic.
I would worry about that more than the scratch.

Looks like they just stuck it in and spun it rather than going in and out for the 45 degree pattern.
 
Apparently was honed by a reputable shop a couple of years ago, been sitting since then. Photo is a little blurry.
 
OK, I have seen it where all the lines were parallel, the hone was spun at one depth with no movement.
Kind of what it looked like in that pic. By the way, that cylinder sealed up fine and didn't smoke either, was a very fast GS 1000.
 
Thanks ray, but I have the current 750 cylinders to bore for the 850 pistons if needs be.
 
Update - guess I should have known better

Update - guess I should have known better

Well thought I'd update this thread for reference.

I've installed the 850 cylinders and pistons, and started the break-in process fairly hard. After warming up the bike I accelerated quite positively to about 7000 rpm and then engine breaked a few times in 2nd gear whilst riding around in a spirited fashion 4 - 6k rpm for about 20km.

There was no smoke on start-up and it's definitely more lively than my old 750 cylinders. In fact it goes really well.

However... having now put over 100 kms on it with two more rides and a bit more hard acceleration etc. It smokes a little once fully warmed up and a bit more after harder riding. Still no smoke at startup at all.

I'm hoping this is still the rings bedding in, but am thinking its probably that ****y little scratch. Unless I went too hard on that first ride.

I'm kicking myself, because it goes so nicely otherwise. But I did take a gamble.
 
Maybe they will bed in but probably not.
If it isn't bad ride it. Carry extra plugs if it smokes really bad.
Buy another cylinder for a winter project.
 
Last edited:
chef1366 said:
Maybe they will bed in but probably not.
If it isn't bad rid it. Carry extra plugs if it smokes really bad.
Buy another cylinder for a winter project.
Click to expand...

The Irridiums do well burning off oil, Dont ask me how I know :(
 
chef1366 said:
Maybe they will bed in but probably not.
If it isn't bad ride it. Carry extra plugs if it smokes really bad.
Buy another cylinder for a winter project.
Click to expand...

It's still better than it was. I'm back to stock plugs whereas they would foul before and I had to run the hotter B7ES.

Guess it only cost me a couple of hundred bucks and a couple of days :(
 
Coady said:
It's still better than it was. I'm back to stock plugs whereas they would foul before and I had to run the hotter B7ES.

Guess it only cost me a couple of hundred bucks and a couple of days :(
Click to expand...
Now you're a member of the "live and learn" club. :D
 
You must log in or register to reply here.

Similar threads

T
1980 GS850GT top end rebuild - head machining
Replies
3
Views
95
first timer
first timer
E
'83 1100E cylinder bores look machine sanded?
Replies
7
Views
103
rphillips
R
R
Considering rebuild or ...
Replies
10
Views
170
rphillips
R
D
Cylinder three running extremely hot
Replies
14
Views
212
Rob S.
Rob S.
G
'83 GS1100E - outside my comfort zone
Replies
17
Views
1K
limeex2
limeex2
Back
Top