• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Seeking tool reccomendations

  • Thread starter Thread starter ujmrider
  • Start date Start date
U

ujmrider

Guest
Hello everyone. I'm a relative newbie and I'm trying to build myself a nice little set of motorcycle tools. Ideally a set that would have everything I need to do most maintenance and small repairs and also be portable enough to bring along on longer trips.
What tools have you all found to be most essential and useful for basic repair and maintenance?
Are there any specialty/lesser known tools (aside from the usual wrenches etc.) that I should definitely have??
Which tools do you find you use most?
Thanks in advance for any helpful advice
 
This may be a silly one, but a little magnet onna stick for when you drop the flat washers from the oil filter cover into the bucket of oil.

Why yes, I did just change my oil, why do you ask? :oops:

But to the point, a couple good sockets, I like Snap On but there are LOTS of other good brands out there. A handful of zip ties, some dielectric grease and a couple connectors (pliers can crimp in a pinch)

Get it? in a pinch? ok, time to step away from the computer...
 
Last edited:
It seems like I use a rubber mallet on my bikes more anything. I'm not kidding either.

32mm socket and 24mm socket for the front sprocket and the rear axle (respectively)

Torque wrenches are a must for garage work, probably not great for traveling though.

Maybe a good set of stubby gear wrenches?

air compressor!!!
 
Try to think in your mind to get a set of everything miniaturized. There is
a neat tool out there at most flea markets and hobby shops that have a ratchet. It has interchangeable bits with a knurled speed loader.

This amazing tool functions as a nut driver with any 1/8" socket, extentions, flat, philips, torx, and other useful bits. Metric Allen wrenches
are essential, so I got a neat little "L" metric set that is only 4" in length
and 1/2" in widths with the handly 6-10mm wrenches.

I have small jumper battery clips screwed onto my neg post of my battery and the pos to my starter solenoid so I can jump any bike or be jumped. I
carry a small thin pocket-size DVM for troubleshooting and a battery status checker with LED lights. It checks the condition of the battery at standstill at 12V or under. It checks the battery at its charging state at above 13.5-14VDC, and I have a very small hygrometer that is also pocket size. It is a droplet with small little beads in it. It check for specific gravity
in the sulfuric acid and costs no more than $2.

I bring with me a small adj Crescent wrench, 8,10, 12, and 14mm open-end wrenches, channel locks, needle nose pliers. I bring anything and everything in miniature scale including Suzuki spare parts in Ziplock baggies. Never ever go out the door on your bike without a spare clutch cable. If your cable snaps, your dead in the water. That is why I prefer
a hydraulic clutch with the same feel over time, and no cable to break whatsever. Cable will fray and wear out and snap after 1000s of engagements and disengagements over time.

Fuses, washers, tie wraps, cotter pins, O-Rings, E-Clips, CO2 patch kit, grommets, superglue, Permatex gasket sealer, solderless connectors, crimper, 18 and 20 gauge wire, tubes of heatshrink, metric cap screws
metric nuts, small container of 10-wt machine oil, small container of 10-
40 wt engine oil, small container of DOT 3/4 brake fluid, butane soldering iron, solder, GS1100 wiring diagram, spare plug, headlite bulbs, turn signal bulbs, instrumentation bulbs, first-aid kit, cell phone, hand-held CB radio, hand-held ham radio, calling card, GPS, etc.... and lots of water and
spare clothing.

All of the above takes very little room, yet will save your ass on a long
trip anywhere you have a breakdown. Like you, I don't want to bring
bulky tools that are unnecessary and worthless to me. I don't want the excess weight either.

Goodluck to you,

KT :-D\\:D/
 
holy cow!!!

on my 750 all i carried was a ratchet, with a universal socket, and a crescent wrench, and a pair of pliers......

i travel light! but on longer trips i would definately be packing some serious butt-saving tools.....
 
I will be taking a 2-3 week Route 66 tour from SF-LA-Chicago on this historic highway next year. I have to brainstorm and think of every conceivable breakdown there is because I may have to go by myself.
And this historic road is lonely and forgotten and neglected. A breakdown could be life or death situation !!

Not everybody has the time or the expense or the raw nerves and adventure to partake in a long road trip like this. I'm the person who
will do it alone if I have to. Nothing intriques me more than on 2 wheels free in the wind and learning about America's pastime.

One thing I will do before I go is to get rid of these Vance and Hine's
4-1 black Supersport exhaust pipes. Never buy a pipe that does away with your center stand AND access to your oil drain plug. This is a complete joke good for the track and but not for the road. If you have
a flat tire, your again dead-in-the-water !! You cannot get the wheel
off nor lubricate the rear chain on its center stand. Just a very stupid design and is a complete turn-off in accessability and ease of maintenance.

My 2 cents again !!

KT
San Jose, CA :-D\\:D/
 
impact driver and torque wrench, in inch-pounds. metric socket set, though just the 10, 12, and 14 mm will do a lot. allen keys, metric. expensive tools are expensive, i have a medium priced husky set that is ok, but i also have an ace hardware "cheapy" socket that is guaranteed forever, too, and only cost 10 bucks for the most common sae and metric sizes. feeler gauges. screwdrivers, in various sizes, esp if you are going to do the carbs.

i plan on putting together a "motorcycle only" kit, with only the sizes on the bike, for travel. there really arent that many different fasteners on these things.

greg
 
You must log in or register to reply here.
Back
Top