Solid State Power Box STANDARD INSTALLATION

[Guest]

Hi all:

If anyone has installed the sspb on a 1000, I was wondering about the wiring change in the headlight bucket?
Got everything wired up right, I think, except for that.
What color wires do you need to use, in the bucket?

https://drive.google.com/file/d/0ByItMzrdJntVRjEtYklzd1BXNmRjeWpHUVZaMm1GMFZFaWdV/view?usp=sharing

https://drive.google.com/file/d/0ByItMzrdJntVWjk5VFlxQWlxOGhaTTBsNkpVbzZrRUJqVGcw/view?usp=sharing

https://drive.google.com/file/d/0ByItMzrdJntVWUVOLXFybDhZMVFoOU9yVW01SF85ZmwwcENV/view?usp=sharing

I know Jim isn't accepting e-mail or I would have contacted him.

Thanks in advance!!

 

[posplayr]

Hi all:

If anyone has installed the sspb on a 1000, I was wondering about the wiring change in the headlight bucket?
Got everything wired up right, I think, except for that.
What color wires do you need to use, in the bucket?

https://drive.google.com/file/d/0ByItMzrdJntVRjEtYklzd1BXNmRjeWpHUVZaMm1GMFZFaWdV/view?usp=sharing

https://drive.google.com/file/d/0ByItMzrdJntVWjk5VFlxQWlxOGhaTTBsNkpVbzZrRUJqVGcw/view?usp=sharing

https://drive.google.com/file/d/0ByItMzrdJntVWUVOLXFybDhZMVFoOU9yVW01SF85ZmwwcENV/view?usp=sharing

I know Jim isn't accepting e-mail or I would have contacted him.

Thanks in advance!!

You can still send an email to: solidstatepowerbox@gmail.com

I'll take a look later tonight.

In the meantime send me an email.

I guess the webhosting for the installation manual quite so please look at so I this is the installation manual.

Download a copy of the install guide. It is a 13 page pdf file.
Preliminary SSPB Installation Manual

Which connections do you have so far?

 

[posplayr]

Also from manual

 

[Guest]

Thank you, Sir!!

I have it over at friends garage, where we did everything but the headlight bucket connections.

He was helping me yesterday, since he solders for living, and we were not sure about the yellow wire from the
harness to the connection in the bucket. The connection from the sspb to the starter relay was also done.

When he texted me last night, after I left, I realize we forgot the yellow wire connecting the ignition switch.
He wasn't sure because of stock wire colors in the bucket, I think. I left him with the manual and sent him a copy of the GS1000 manual so he could see the diagram.

When connected the fault light came on but no ignition. Then he thought that the ignition wasn't connected....

I will get back to you privately, thanks again POSPLAYER!

 

[posplayr]

The Yellow pigtail on Molex Pin 4 of the SSPB is the START input (from kill switch push button start) in order to cutout the headlamp during startup. As indicated in the table connect to the Y/G (Yellow/Green) You can easily find this wire at the solenoid. It looks like this is connected correctly.

The other signal that is probably confusing you is the IGN ON signal which also comes from the kill switch to indicate the ignition should be on. This involves the O/G output of the kill switch.

You can route a separate wire from kill switch to the SSPB , but there is already one available (Lg/W) when you got rid of the stator headlamp loop.

This diagram in the manual shows a typical set of changes. Your may be slightly different but the wire colors will be the same.

 

[Guest]

Thanks Jim, for the responses!

I think the IGN ON signal is what we need to be concerned with.
I will get back to the bike's location and finish up, hopefully this weekend.