• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Stoping gear crash (N to 1st) by holding in clutch

  • Thread starter Thread starter shortlid
  • Start date Start date
S

shortlid

Guest
Just thought I would let you guys know, what I have found. We have non-syncroed trannies. So going from N into gear even with the clutch pulled all the way in produced a gear crash. I have found that even with 20W-50 if I can anticipate the light I am at I can hold in the clutch for 1 min. BEFORE I put it into gear while still in N. This lets the tranny gear stop rotating and I get a nice gear change with out teh crash. Just thought I would share, many might have already known this. :oops:
 
Id bet your clutch needs some attention, it shouldnt take a minute to get it to shift without more than a little "snick" into gear.

the new GS1100 I was around in the mid 80s didn't ever make any more than a little "thunk" when shifted to first from a standstill, and never was there a "special" procedure to make it happen.

my 850 seems to need the clutch looked at for similar reasons, Im putting it off til the engine runs well, but it doesnt disengage completely even with cable freeplay set to the tight side. I assume clutch steel and friction plates will solve this.

my car has an unsynchronized first gear, and shifts into first effortlessly as well, at least from a stop, there shouldn't be any reason for your bikes tranny to not operate the same way.
 
Clutch just replaced?

Clutch just replaced?

The metal and friction plates in the clutch in my '80 GS850G was replace about 5,000 miles ago! I think it has to do with the gears still being in motion just after the clutch is pulled in. if you give the gears time to slow down they don't "snick". :D
 
A 'crunch' isn't really accetable - something is getting warn out. My 850 usually 'clunks' into 1st gear (no waiting). It often just 'clicks' into 1st gear. The only time I get a 'crunch' is when the engine oil is cold and the choke is spinning the engine too fast. I've owned other shaft drive bikes (BMW), and it always 'clunked' into 1st gear. It's just something inherent in the breed.

Also, I often put my bike into first while I'm still moving - so I'm not sure the transmission is 'non-synchro'.

Ace.
 
A motorcycle trans does not have syncros like a car. If it clunks bad try adjusting the idle speed If it is too high it will clunk more
 
Get into first before you stop and just hold the clutch in. Good exercise and saves the "crunch". The only time this might be bad is if you have a clutch drag problem.
 
so this would explain the times I pull the clutch and hold it without gearing down as I come to a stop, my gears will get stuck and not change down until I let the clutch out just to the point it catches to get the gears all in motion again, then I can go down!
 
snowbeard said:
so this would explain the times I pull the clutch and hold it without gearing down as I come to a stop, my gears will get stuck and not change down until I let the clutch out just to the point it catches to get the gears all in motion again, then I can go down!
Click to expand...

No, I don't think it does :lol:
 
You must log in or register to reply here.
Back
Top