• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

What is the advantage of DYNA 2000

  • Thread starter Thread starter 00.
  • Start date Start date
0

00.

Guest
I was looking at getting a dyna 2000 kit for my 1982 katana, I understand the dyna 2000 has adjustable advance, and a rev limiter but I'm realy not sure what the benefit is of an adjustable advance, how will I get more power by adjusting the advance??? versus the dyna S which does not have the adjustable advance..... Curently I have a 1180cc motor, yoshi exhaust, 33mm mikuni carbs, yoshi cams, and dyna S... the bike runs great but I was just wondering how I would benefit with a dyna 2000 on this kind of set up... Just don't understand how or if I can get more power out of a dyna 2000 over just the dyna S....
 
I don't have a clue ,but with 1180cc, a rev limiter sounds useful. But since "the bike runs great" why do anything but ride?
 
You can use the adjustable advance at the drag strip on your drag bike.
IMHO, don't waste the time or money on a street bike.
 
I'm not familiar with that unit, but the idea is to advance the timing as much as possible, throughout the rev range, and bring the engine to the edge of detonation. Modern cars have "knock detection" sensors, and the timing is adjusted accordingly automatically.
 
tom203 said:
I don't have a clue ,but with 1180cc, a rev limiter sounds useful. But since "the bike runs great" why do anything but ride?
Click to expand...

Yes, I would think the rev limiter is the only benefit to the OP.;)

I don't have one and it doesn't worry me too much unless you do wide open speed shifts
 
It does away with the mechanical advancer and if you plan to boost it or run nitrous then it has a wire you can hook up to retart the timing. Also I think it provides additional retard for startup, but I have been wrong once before.
 
Nessism said:
I'm not familiar with that unit, but the idea is to advance the timing as much as possible, throughout the rev range, and bring the engine to the edge of detonation. Modern cars have "knock detection" sensors, and the timing is adjusted accordingly automatically.
Click to expand...

So basically the unit compensates electronicaly for the mechanical advancer??? Also how you do know that you are getting the edge of detonation on an electronical advancer, is there a way to check for the optimal preformance curve??? everyone will just telll you to advance it to 35degrees or all the way up to 40 degrees but they are just kind of guessing how can I adjust it properly is there a way to measure the perfect detonation, I'm a bit confused on how you can adjust this unit properly, its cool to just have the bike run right but if I have adjustments options onthe dyna 2000 unit how can I measure if the adjustments are optimaly set, that is the million dollar question...
 
The instructions, which can be downloaded from dynatek, show all the advance curves that you can select on the 2000. They also tell you which curve to select for a stock bike and how to set the timing.

There isn't really a way to tell when you are getting close to pre-detonations (pinging) other than a knock sensor and associated hardwar($$$). Google around and you should be able to help you read your spark plugs for evidence and also listen for pinging. There are things other than ignition timing that affects pre-detonation such as cam timing and fueling.
 
I run one and like it.
It also has a lead for an electronic tachometer.
Very easy to time with a degree wheel built in to the crank trigger rotor and a timing light on the box. You set the advance and tell the box how fast you want to get there.
 
The Dyna 2000 is really for performance engines.

I run one on my turbo bike.

You get a few really nice capabilities.
It is programmable - the base unit comes with a handful of advance/retard curves preloaded into the box. These are selectable with a dial. It also hs a built-in rev limiter to protect you from zinging the motor. If those don't meet your needs, Dynatek has programming software called curve maker and a cable (sold separately) that allows any computer to remap the ignition curve and rev limit to your custom settings.

There are wires to feed electronic tachs, and wires you can use for boost and security cutouts. On my turbo bike, the ignition retard kicks in when the boost sensor detects preset pressure.

These units are designed to allow a lower resistance coil (2.2 ohms) so you get a higher intensity spark.

I've run one for 3-4 years now on my turbo bike. What's nice is I can change the igntion settings just by turning a switch. This allows me to have different maps for hot humid weather or cold crisp days.

BTW, I also run an air/fuel sensor on my bike to know the fuel mix. I plan on upgrading that this year to a combination boost and air/fuel unit with a data recorder.

http://www.aemelectronics.com/wideband-air-fuel-systems-15/wideband-failsafe-gauge-84/
 
Last edited:
You must log in or register to reply here.
Back
Top