• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Where did the Compression go????

  • Thread starter Thread starter michael
  • Start date Start date
M

michael

Guest
I have a 81 GS850L parts bike I bought to help get my 80 GS850L on the road. The motor made the usual " da da da Daaaa da da da daaaaa" sound when cranking that let me know that one cylinder had bad compression. Sure enough, when I did a test, cylinders 1 to 3 had around 130 to 140 PSI, but #4 had about 20 to 30. I had seen this before on another bike, and it had a dime sized hole in the piston when I disassembled it.

I disassembled this motor and I don't see anything wrong!!! The piston and rings are fine. The head gasket is ok. The cylinder looks perfect and the head looks ok. The valves look to be seated up in the head properly.

Maybe the valve seats are bad and I can't tell from looking?? This is the only thing I can think of.

I want to try to sell the head to fund my tight budget GS850L project, but I can't if I suspect it is no good....

Anyone have any ideas??

Thanks,

Mike.
 
Do you have adequate valve clearance on #4? A valve that doesn't close all the way will cause very low compression.

Did you dump some engine oil down the plug hole of #4 and retest? If the rings are bad, this will bump up the compression a noticeable amount.
 
flyingace said:
Do you have adequate valve clearance on #4? A valve that doesn't close all the way will cause very low compression.

Did you dump some engine oil down the plug hole of #4 and retest? If the rings are bad, this will bump up the compression a noticeable amount.
Click to expand...


This is always a good test if you want to rule out the bottom end.
 
Thanks for the quick responses!

I did not put any oil in the cylinder and try it again. I thought with such low compression something catastrophic had happened. The engine only had 17K miles on it. If the valve had worn down that much, it must have begun to be noticeable to the previous owner before it got so bad that the compression was that low?

I know what I will do next time though... before I tear it apart!

Thanks again,
Mike.
 
Yea, if you run through the troubleshooting to the end, then you'll have it narrowed down much better.

Like they said, a squirt of oil in the cylinder - if the compression jumps up, then it's the rings, if not it's the valves.

If it's the valves, loosen and adjust them on the cylinder in question. If they are too tight the compression will be low.

After that, take the wrench to it if the compression doesn't improve. You'll have a good starting point.
 
You must log in or register to reply here.
Back
Top