Announcement

Collapse
No announcement yet.

GS1000 streetfighter idea w/ picture

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Ed Vrolijk
    Guest replied
    Hi PJ,
    Just read your first couple of posts in this thread again. Look how far you have got. Well done!!!!
    I was amazed as well as how many guys tried to convince you to keep it stock.
    AND NOW RIDE IT!!!!!!!!
    Have fun,
    Ed

    Leave a comment:


  • YoshiJohnny
    Guest replied
    I just had a look back at the whole of this thread and gotta say big respect for all the trials, tribulations, ups and downs as well as the commitment shown through the build. Thanks for keeping us glued intently with your updates and I hope it inspires others to do the same.

    What I couldn't believe is the number of folk who actually were negative about this project. Now I know there are the purists who want to keep every nut and bolt as Mr Suzuki intended and that is well and good for those who want a showpiece/investment/easily maintained standard bike.
    I never owned a bike I didn't modify to suit me and to be honest riding a standard 25 year old GS would not interest me at all, I ride all year round in British (which is an anagram of bloody ****ty) weather and get to use all the new Busa's and B'King Gixer etc demo bikes from work. I wanted something different, a bit of a challenge, something not many can be bothered to do. Any idiot can get his visa/amex card out and buy the dream....few can build it themselves.

    Well done PJ, hope it brings you loads of grins

    John

    Leave a comment:


  • 80GS1000
    Guest replied
    Thanks for all the comments/compliments guys.

    Also a huge THANK YOU to everyone here. This project could've never been done without your priceless insight, knowledge, encouragement and constructive criticism.

    Leave a comment:


  • Suzukfan78
    Guest replied
    Looks Great!

    I just had to give you props on an excellent job 80GS1000. Ive been following this thread for some time and its really cool to see you get want you want out of your bike. We are all so lucky that people like you are on this site helping everyone with what aftermarket/custom stuff works on the GS1000. Your bike looks GREAT and I hope to see it someday in person. Mabye the next Western states rally.

    Leave a comment:


  • posplayr
    replied
    OK I'm still a little confused



    PJ,

    Earlier you said you thought you needed to take about 2-3 inches off of the down tube length. This is probably before you did any cutting on the pipes. In reallity all you had to do was cut off the last 3 inches of the pipe and weld on the V&H collars and flanges. I have been looking at those Hindle pipes over and over looking for a cut but could not find one. Was going to write you must have a hell of a welder.

    Bottom line the pipes fit further back than you originally thought and so the 2-3 inches out of the down tubes was not required. You also thought you were going to have to modify the mid tube? Sounds like other than getting the muffler to fit there was little in the way of clearance problems.

    Sounds like an awesome solution. I wish I would have looked at it closer in Carson City. With your success, I'm looking to adapt one of the GSXR1100 headers to my Yoshi ; it is OK for the time being but it isn't in good enough shape to ceramic coat. All part of a longer term plan for GSXR conversion.

    Posplayr

    Leave a comment:


  • first timer
    replied
    don't get me started. i know what you mean i am doing my price and part list now and it adds up quick. You running dyna s ignition?

    I am working with Speedy steve over on old skool and he is a big fan of the msd mc-3 ignition if you are looking to burn a few more dollars.

    word of advice speedy steve (ex drag racer) was recomending that to help pay for all this work once it's done start taking it to weekend drags.

    Originally posted by Tarbash 27 View Post
    ace hardware allen bolts, back and forth matching them up every day. I ordered every gasket from bikebandit. I went through every diagram and picked everything. Of course i forgot a few seals and gaskets here and there, but I made a second order, than decided to to make another order. I must have spent almost $450 on gaskets, seals, misc bolts, washers, intake boots, just from bike bandit. I have the list downstairs in my garbage can with about 90% of the stuff. I bought the gs1000 donor bike for $125 and spent about $2500 on this motor already, the crank work will be about another $600.

    Leave a comment:


  • Tarbash 27
    Guest replied
    ace hardware allen bolts, back and forth matching them up every day. I ordered every gasket from bikebandit. I went through every diagram and picked everything. Of course i forgot a few seals and gaskets here and there, but I made a second order, than decided to to make another order. I must have spent almost $450 on gaskets, seals, misc bolts, washers, intake boots, just from bike bandit. I have the list downstairs in my garbage can with about 90% of the stuff. I bought the gs1000 donor bike for $125 and spent about $2500 on this motor already, the crank work will be about another $600.

    Leave a comment:


  • first timer
    replied
    what bolts did you use on inside of the motor new philips?

    you got a part number list of all the little seals and what not i need to order for when i tear down my motor and build it from the crank up?

    I can look the stuff up but if you already did.....

    ok cool that will help, I am hope the 16v gs750 oil gears i have are the same as above. I think they are.
    Last edited by first timer; 07-30-2008, 11:41 PM.

    Leave a comment:


  • Tarbash 27
    Guest replied
    this is what I bought


    Leave a comment:


  • Tarbash 27
    Guest replied
    Well Im waiting to send the crank out to be done. But Im a bit low on funds now. I figure motor will be built and complete end of august. Then I will have to take out my 750 motor. I will be doing some things to the bike such as changing gauges, possibly putting 37mm gs1000 forks on from the donor bike, and major cleaning from all the grime and leaking fluid over the years from the original motor.

    I did not make a thread. I dont like typing alot. I was going to use stock cams gears, but maybe I should buy a set of ape adjustable gears. I got to learn to do the valve timing stuff.

    I also did a gorilla clutch kit myself. I bought the kit and ape clutch nut. High volume oil gears, replaced all philip bolts inside motor. I did not get a manual adjuster yet but I will. All new intake boots, clamps, stainless bolts everywhere, all genuine suzuki gaskets. Plus im torqueing every single nut and bolt to spec.

    When you mentioned power wheelies, you made me smile!!

    Leave a comment:


  • first timer
    replied
    who ported your head?

    are you doing anything with the clutch or clutch basket?

    i have heard and read from many sources that it is the weak point of a built motor. You don't want your clutch to go bang and take out your oil pump.

    either of you guys try fitting 750 oil pump gears in a gs1000 motor?

    Originally posted by Tarbash 27 View Post
    oh, Im already running a pingel and 29mm smoothbores on the 750 that will got on the 1085. I got ape high lift springs in a ported head. Im doing everything from the ground up. I replaced every seal and gasket in the entire motor. Cleaned every single part and crevice. Loctite on every nut and bolt, etc.

    Did you use stock cam gears or adjustable gears?

    Leave a comment:


  • 80GS1000
    Guest replied
    Originally posted by Tarbash 27 View Post
    oh, Im already running a pingel and 29mm smoothbores on the 750 that will got on the 1085. I got ape high lift springs in a ported head. Im doing everything from the ground up. I replaced every seal and gasket in the entire motor. Cleaned every single part and crevice. Loctite on every nut and bolt, etc.

    Did you use stock cam gears or adjustable gears?
    Dude, that's gonna be a beast. How much longer you think till you take the maiden voyage? It's gonna dislocate your shoulders from pulling so hard. You have a project thread? I'd like to see your progress....

    I got a set of Falicon adjustable cam gears for the GS1000, degreed in. Dunno if they're commercially available anymore; an oldskool GS dragbike mechanic locally had them sitting on a shelf. Are you using a manual camchain tensioner?

    Leave a comment:


  • Tarbash 27
    Guest replied
    oh, Im already running a pingel and 29mm smoothbores on the 750 that will got on the 1085. I got ape high lift springs in a ported head. Im doing everything from the ground up. I replaced every seal and gasket in the entire motor. Cleaned every single part and crevice. Loctite on every nut and bolt, etc.

    Did you use stock cam gears or adjustable gears?

    Leave a comment:


  • 80GS1000
    Guest replied
    Originally posted by Tarbash 27 View Post
    Looks great, I like the paint alot. How's the powerband with those cams? Notice a bit more topend? Im putting the same ones in my 1085 motor I'm building for my 750.
    A GS 7/11? Niiiiice.

    With the gearing stock at at 2.8 (17 front, 48 rear on 520 chain), the powerband starts at 4000 RPM and goes like warp speed up to redline. MUCH MUCH MUCH more midrange and topend. I have a hard time keeping the front end on the ground in 1st and 2nd when accelerating at WOT. Hope you like power wheelies.

    Are you going to be using high lift valve springs? Web Camshaft sells a set of Kibblewhite high lift valve springs for the GS1000 motor if you need them.

    Also, you might want to look into getting a Pingel petcock to keep up with the increased demand for gas and avoid stumbling due to fuel starvation....

    Leave a comment:


  • Tarbash 27
    Guest replied
    Looks great, I like the paint alot. How's the powerband with those cams? Notice a bit more topend? Im putting the same ones in my 1085 motor I'm building for my 750.

    Leave a comment:

Working...
X