Announcement

Collapse
No announcement yet.

'81 GS550 Cafe Build

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hone101
    Guest replied
    That's a nice looking fastback in the background there.

    Leave a comment:


  • BigD_83
    replied
    The SRX is/was essentially a cafe bike out of the box. Light, nimble, good brakes, without a lot of extras. The exhaust sounded good but was somewhat restrictive. There is an entire world of aftermarket parts available to make it one's own.

    Always thought it'd be fun to have a one-design racing series with these little bikes.

    They pop up every once in awhile, in disparate parts of the country. I've only seen a few in Canada that were not Japanese gray-market imports. There was a dealer with one somewhere in the Great Lakes states (Illinois, maybe?); another red one with very low mileage.

    Leave a comment:


  • D-Mac
    Guest replied
    Originally posted by BigD_83 View Post
    I had to look the CL77 up...wasn't sure if I knew what model that was.

    Gorgeous if done right, yes.

    Speaking of the SR500, my personal favorite super-single, the SRX-6, still holds a special place in my heart but is probably newer than most would be looking for as a cafe build (picture not mine):



    There is a nice gallery of custom/restomods here
    Funny you should mention the SRX-6. I was just eyeing one for sale today.....hmmm..... I kind of like the look of 'em in stock form.

    Leave a comment:


  • D-Mac
    Guest replied
    Some progress this weekend. Not the most exciting stuff, but it brings me closer and closer to the end of this project. I started by cleaning the harness with a combination of acetone, ethanol (to wipe the dirt and crud off gently) and electronic cleaner. I pulled each connection apart, cleaned it, added a little dielectric grease, and reconnected it. After sorting out the wires on my new speedo and tach, matching them to the appropriate wires on the harness, and uncrossing my eyes, I soldered on the new wire and crimped/soldered new connectors, and stashed it all inside the headlight. So the front of the harness is mostly done (I hope). I haven’t hooked up a battery yet (too many bare wires on the rest of the harness to risk it), although I tested each of the connectors/lights that I modified by using a volt-meter and 9v battery.

    I have to sort out turn signals, although the wires for the front ones are in place.

    A pic of the first few wires in the bucket. When I was done the bucket was FULL. Once I know everything works, I will go back in and remove all of my multi-colored labeling tape!


    Next, I started to work backwards on the harness. By gutting the entire mid-section of the bike (old battery box, which held the reg rec, fuses, spark box, solenoid, etc. there are a LOT of wires and components to sort out. Added to that, this harness has a lot of “homemade” modifications, all of which are pretty awful and need to be corrected.

    Exhibit A. This pile of misc. fuses is supposed to be a fuseblock with four fuses on it (not three in-line). Note the bare “hot” wire poking out! There are a LOT of these wiring jobs on the harness. I have the fuseblock from my “spare” harness, but it’s a little melted and missing the cover. I like the size and style of the block (even if it is a little dated), so I ordered a complete replacement from a GS for $6 on eBay.


    Hmmmmm…..this isn’t gonna work.


    This is supposed to be a 10-amp fuse.


    A pic of the proper style fuseblock (bottom shown).


    I’ve decided to do the “coil relay mod” that a lot of GS owners do. In fact, anyone with an old bike might want to consider it. The wiring to the coils runs through the entire harness and several switches before reaching its destination. Along the way, voltage can drop substantially, which affects the spark quality. The mod uses the existing wiring to trigger a relay, so I can then run “clean” power straight from the battery to the coils (via the relay). It requires a little cutting into the harness to complete, but now is the best time I guess. Good thing too because look at what I found as soon as I opened it up to splice it….bare spots on one coil “feed!” This is normally taped into the harness, so there would be no easy way to spot it if I hadn’t decided to tackle the relay mod. This might help explain why two cylinders were misfiring before.


    I still have to run new wires for this mod. I also have to clean some additional connections, replace a broken oil sensor switch, and re-do some burned-out connectors that run to the stator. I’m also eliminating the silly loop through the headlight that runs through one stator-leg. I’ll be removing the large and unneeded “accessory panel” too.

    In addition to that stuff, I also started laying out where I want to put various electrical components. I’m trying to stash as much as possible onto the little shelf I made behind the seat “bump.” The reg/rec, solenoid, and main plugs will just reach properly if I put them toward the front of my shelf. That leaves the battery in behind, along with a few other gadgets. I’m stashing the transistorized (pre-CDI) box just in front and under the seat on a shelf that I kept from the original frame. I think I’ll try and get this stuff bolted down soon, so that I can begin the process or measuring and making wires to reach other components (there will still be many connections in need of modification). I’ll be replacing the major cables to the starter, main ground, and battery-to-solenoid as the old ones are thin, worn, and no longer the correct lengths.

    I also measured for new clutch and throttle cables because the old ones are ruined and they are now way too long anyway (there’s a big difference between pull-back bars on risers and clip-ons!) This bit of “fun” meant pulling the carbs so that I can fit a new cable. I’m hoping to get the new cables ordered this week.

    In summary, I’ve learned a lot about wiring and I have many things started, but tons left to do. This experience should make the motorcycle electrical course I take next month a lot easier! Hopefully I won’t learn that I did it all wrong.

    Leave a comment:


  • BigD_83
    replied
    I had to look the CL77 up...wasn't sure if I knew what model that was.

    Gorgeous if done right, yes.





    Speaking of the SR500, my personal favorite super-single, the SRX-6, still holds a special place in my heart but is probably newer than most would be looking for as a cafe build (picture not mine):



    There is a nice gallery of custom/restomods here

    Leave a comment:


  • Sci85
    replied
    I learned the wiring is not that bad actually. I'm sure you will have no problem and even if you do, someone here already knows the answer! Keep plugging away, a little bit everyday.

    Leave a comment:


  • D-Mac
    Guest replied
    Originally posted by koolaid_kid View Post
    Restore a CL77. They were, and still are, a work of art.
    Agreed. I think they are one of the most beautiful motorcycles ever produced. I'd love to own one.

    Leave a comment:


  • koolaid_kid
    Guest replied
    Restore a CL77. They were, and still are, a work of art.

    Leave a comment:


  • D-Mac
    Guest replied
    Originally posted by BigD_83 View Post
    It's been awhile since I've looked in on your rebuild. Looking really, really nice!

    I bet you have plans for another rattling around in your head?
    Damn. You're on to me! Still lots of work to go, but the electrical is coming along nicely so far. I have all of new gauges wired for the harness. The charging circuit is BAD, and all of the wires rear of the engine are basically toast. One I get the harness a bit cleaner, I'll be able to lay it on the frame and start planning locations for the various bits.

    As for my next project, I was originally thinking of trying my hand at a Norton or old Triumph. A friend had his Commando 750 in my garage for a while, and it was cool. We finished it, he got it running, and it went home. Heavy bike though, and the isolastic mounts were less than fun to deal with. I'm thinking of something else.

    Right now, I'm think of thinking of a big single or a twin. Something different. A Yamaha SR500 tracker would be cool, or maybe a basic resto on an older Honda (something pre-1968).

    I've also lusted for an early gen VFR. Hell, an old naked Wing would be a fun project too.

    Leave a comment:


  • BigD_83
    replied
    It's been awhile since I've looked in on your rebuild. Looking really, really nice!

    I bet you have plans for another rattling around in your head?

    Leave a comment:


  • 6pkrunner
    replied
    Incredible work! That is just plain gorgeous.

    Leave a comment:


  • Tim Tom
    Guest replied
    Wow this is a beautiful build. You made some incredible progress from the redneck rocket.

    Can't wait to see it with that pipe on. Even though it's a 'cheap' MAC it will still look fantastic!

    Leave a comment:


  • D-Mac
    Guest replied
    Bike has no wiring yet, so it'll be a couple of months before I get that done. Relocating everything to fit under the seat will be a bit of a challenge.

    Leave a comment:


  • Sci85
    replied
    Love this build d-mac! Keep it coming!!

    Leave a comment:


  • musicman
    Guest replied
    That thing looks amazing!

    Leave a comment:

Working...
X