• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Recommendations, boring, ballancing

  • Thread starter Thread starter Guest
  • Start date Start date
Ran like crap at first so I put 150 mains in. That made a huge difference and there's throttle response now. That might be too much but id rather find out its rich than lean. I ran it for all of two minutes just to set the screws a bit for a better idle.
Thing sounds like a sewing machine though, I'm going to have to adjust the valves to quiet it down.

What should I set the valves to ? I thought I did pretty good setting them the first time. The right side sounds ok... or as expected. The left side is louder.

How long and what RPM for cam break-in?

What about heat cycling and re-torquing the head ?

How should I set the APE cam chain tensioner?

I can't remember this stuff. I'm sure Ray told me a while ago :P


117.5 main jets feel way too small, There was no throttle response at all.
150's seem to work ok, It will respond to throttle but I can't really tell for sure yet because I don't want to rev it.

Engine seems well balanced at low rpm, no vibration at all. Even smoother than stock was.
Starts at first crank ( if my battery will do it) There is definitely more load on the starter to turn it over.
 
Wow. That thing sounded sweet. Very...Hot Rod like. It's kinda strange to have that hot of a motor in a laid back half liter cruiser. The ultimate sleeper bike maybe?
 
.03-.08mm and most of us set the exhaust to .08 to .12mm.the exhaust have a habit of receding into the head if the engine is run hard and lean conditions seem to make it worse.With the .08-.12mm settings,I expect to get around 8000 miles before having to change shims again.
 
I know what happened. I used 3-8 thou. That's supposed to be 1 to 3 thou. My feeler gauges are hard to read. And at 4am I must have just been too tired.
 
Last edited:
My PC is playing up with Youtube :(

I shall have to look and listen later, but glad she's running!
 
Try another browser. Like chrome or firefox.

I had it out today for breaking in the cam's. Looked for leaks everywhere, tweaked the low speed screws a bit. So far its looking promising.

Haven't taken the valve cover off yet but it does get a bit quieter when its warms up.

I noticed the timing chain tensioner was backing out a little bit. So I turned it in until the noise stopped and then out 1/4 turn. There was only a slight bit of pressure stopping the bolt from turning in anymore.


I did notice some vibration this time. Sitting there at idle the whole bike sort of floats up and down a bit but smooths out above 2000. At idle its pretty cool to see :D

Drove it around the driveway a bit and it feels smooth and wanting to go... Hard to tell when I can't rev it yet though.


Definitely need a new battery. It keeps a charge but is difficult to charge and barely turns the engine over. Kind of seems like an overbored Hardly the way it struggles to turn over and then catches :P
 
Last edited:
Mekanix said:
I know what happened. I used 3-8 thou. That's supposed to be 1 to 3 thou. My feeler gauges are hard to read. And at 4am I must have just been too tired.
Click to expand...
The usual spec for aftermarket cams is 5-6 thou. I usually run between 4 and 5.
 
If you use the stock GS500 tensioner.Back it out until it locks.Then just turn it enough to let it snap out.It's set.If it doesn't snap out,the tensioner spring is to weak.I don't know how the GS400.425.450 tensioner is made.
 
Mekanix said:
Where do you check them?
Click to expand...
Between the valve and rocker adjuster screw. The manual shows what position the cams should be in for which valves to set. You go by the notches on the end of the cams and whether they are facing away or towards each other.
I like to adjust my manual tensioner with the valve cover off, that way I can pull on the chain in between the sprockets to see how tight or loose it is.
 
Stephen, the valve clearances on THOSE cams is supposed to be .005, (five thousandths of an inch). Ray.
 
Got to see the vid's at work today... oh yeah! :D I like it :D

I wonder how long 'til you wanna put clip ons and rear sets on the L...
 
Found out why I had a rocker ticking. When I set them the first time, the cams were still painted. The paint came off after a while so I was able to set them more accurately.
Just got it licensed again so I'll be working on it more now.
 
Had the bike out for a run today to see what it would do. Carb settings for the moment really suck :P

It ran different than it used to. The rough vibrating at 5k is completely gone.

It has a small vibration at 2500 and then between 3-4 then 6500-7 but cruising around 5k is so smooth that I can see clearly in my mirrors and this bike has no dampening for the engine or handlebars.

At the right idle on the center stand you can feel the ground shaking a bit :P

It does pull through the RPM's but takes too much throttle to get it up there as if its delayed as the slides are going up slowly. Time to start tuning.
 
Excellent, sounds promising :D

Definitely sounds like it's time to maybe trim the slide springs and maybe enlarge that vacuum port ;)
 
How do your plugs look? I wouldnt want you to lean it out and burn a piston.
 
You must log in or register to reply here.

Similar threads

X
Big Bore or Piston Options for 1980 Suzuki GSX400E
Replies
6
Views
83
Syd
Syd
c130Marine
1983 GS1100E roller
Replies
0
Views
63
c130Marine
c130Marine
Bobbys 94
78 GS750 engine overhaul on the Cheap!
3 4 5
Replies
81
Views
734
rphillips
R
E
'83 1100E cylinder bores look machine sanded?
Replies
7
Views
106
rphillips
R
K
Hanging idle troubleshoot help
Replies
18
Views
298
Naulty
N
Back
Top