• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

1000 motor into an 850?

  • Thread starter Thread starter dwarf8
  • Start date Start date
... the carbs magically synchronize

... the carbs magically synchronize

Maybe the title wasn't catchy enough?

"Roast baby - what's the best wine to serve?"
"Naked bikes - men without chaps"
"If I show you my gears will you clutch them?"

Does anyone have any ideas on this (the motor swap) issue?
I'd rather not start it and find out I have 3 months serious fabrication ahead of me. :)

The answer I'm hoping for is "It bolts right in and the carbs magically synchronize!!!"
 
Looks like no one has any experience with this particular swap. I don't know much, but here's what I know...

The 850 used the 1000 frame, so that adds to the possibility it will work.

The 850 engine, however, is a 750 engine that's been bored out, so that's a strike against.

A number of folks have done '7-11' conversions with the 1100 engine in a 750 frame - that's backwards from what you're asking, but threads on that conversions might point out where there will be challenges.

Both should either be L models or both should be non-L models.

I assume the 1000 was a G (shaft drive) model. Mixing chain and shaft creates severe complications.

The closer to the same year the better.

My guess is it can be done, but it's hard to tell how hard it will be. If you have access to both machines, I'd do a lot of measurements to get a rough idea how much fabrication you'll have to do.

Not a lot of help probably, but it's all I got.....
 
I'm going to give it a try - from what little I've found on the topic, it shouldn't be too bad. The only thing I've found is that the motor mounts will need to be adapted/changed.
 
"1000" is not specific enough -- is it a shaftie engine?

If both donor and recipient are G models (shafties), then a 1000G or 1100G engine will bolt right in. You'll need the driveshaft from the donor bike. The chassis are otherwise identical.

As far as using the 850 carbs, I know the carb bodies are the same, but I'm not sure about the carb spacing -- it's quite likely to be the same, but I'm not going to swear to it. The main jets are the same, I think, but the needles are different and possibly the idle jets, too. Best to spend some time with the fiches.

I'm also not sure about whether the 850 exhaust fits the 1000G/1100G engines. Again, a microfiche part number comparison would be helpful.
 
Isn't the GS1000S also a shaftie?

Also - why did Suzuki make nearly identical bikes in 1980 - the GS1000L & the GS1100L?
 
Last edited:
I bolted a 1980 GS1000G engine right into my 82 GS850L. The driveshafts ARE the same. Motor mounts ARE the same. The carbs are different- 1000 has 34mm, the 850 had 32mm, the carb bodies ARE NOT the same. My Vance and Hines exhaust bolted right up.
The only external visual difference between my 1000 and my 850 engines is the longer and larger intake runners on the 1000. It had larger carb boots too.
Simple swap!
 
Thanks!!

Thanks!!

Many thanks to all for great info.
They are both "L", shaft driven bikes. The 850 motor is shot and the 1000 was bought without a title in boxes and crates but it's all there including the carbs. (It actually made it home in the back of an '89 Honda civic wagon. Photos available on request!)

From what I'm hearing it's at worst worth a shot and at best a bolt in.
Look for parts for sale once the swap is completed.

So tell me, what was it....
The 'baby' one? :)
 
It's an easy swap. I am planning to do it some day I even have the GS1000G motor under my workbench. You should change the carbs 32 vs 34.. I just bought a set of GS1000 carbs for mine. The drive shaft, It depends on the year, the earlier GS850 79-80? used a smaller bolt pattern than the GS1000. the later one's were the same
 
You must log in or register to reply here.
Back
Top