• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

'82 gs1100gl. Shift lever not returning to center

  • Thread starter Thread starter Guest
  • Start date Start date
G

Guest

Guest
Just bought this bike, 8600 miles but had not been started for a year or so. Had to give the starter a little TLC, some fresh gas and got it started. Warmed up and changed the oil (MC 10w-40) and filter, old filter was pretty clean. Only real problem so far is the shift lever dosen't snap back to the center detent after up shift or down shift, I have to bump it a little with my toe to make the next gear change. The clutch is adjusted per manual. After a 9 mile test drive it was maybe a little better or just wishful thinking ? Is spring 25 in the parts diagram a suspect problem ? I'm going to have to pull the carbs and clean them before I take it on the road again, a first gear bog and refire is pretty exciting...... Maybe a few more miles will free up some sticky parts. Thanks, Jim
 
jljim said:
Just bought this bike, 8600 miles but had not been started for a year or so. Had to give the starter a little TLC, some fresh gas and got it started. Warmed up and changed the oil (MC 10w-40) and filter, old filter was pretty clean. Only real problem so far is the shift lever dosen't snap back to the center detent after up shift or down shift, I have to bump it a little with my toe to make the next gear change. The clutch is adjusted per manual. After a 9 mile test drive it was maybe a little better or just wishful thinking ? Is spring 25 in the parts diagram a suspect problem ? I'm going to have to pull the carbs and clean them before I take it on the road again, a first gear bog and refire is pretty exciting...... Maybe a few more miles will free up some sticky parts. Thanks, Jim
Click to expand...

You would have to show what the spring 25 is, but at the end of the shift shaft is the shift mechanism. It works with a spring and the star on the end of the shift drum. If that is the spri g you are talking about, you'll have to pull the clutch basket to check it out.
 
I have not looked up your "spring 25", but here is the spring that keeps the lever centered. You can only see the ends straddling a post through the triangular hole.

gearchange2.jpg


Some time ago, I was working on a bike that would shift in one direction, but not the other, and found this:

gearchange.jpg


I don't think that would be your problem this time around, so check that the spring is intact, but you have to look behind that plate with the triangular hole, after removing the clutch basket.

.
 
Pull the clutch basket and have a look....the forked return spring could be tired. If so, it might be saved by bending.
 
I found the spring behind the plate the on Partzilla "Gear shifting" diagram. Looks like it's still available from the dealers. The tach cable is also broken. I wasn't impressed with the aftermarket cable I got for my 650 Kaw so I'm going with OE on this one. Thank you, thank you for the pictures and all the replies. It looks like the clutch housing has been off before, so it probably needs a look anyway.
 
Check the action with the clutch cover removed or loosened; I've seen the shift shaft bind against the cover when a thinner aftermarket gasket was used.
 
Just wanted to follow up on my original post. The carb work is done, lots of plugged up ports. Starts,idles and runs excellent. After a few more miles of wishful thinking, the sticky center detent on the shift did not fix its self.......I had a new tach cable, air filter and side cover gaskets bought, so got the tools out and got busy. Taking the advice from bw, I loosend the clutch cover and was rewarded with a positive center detent. The cover had been replaced with no gasket and silicone sealer and was binding on the end of the shift shaft. Cleaned off the silicone and reassembled with an OEM gasket. Only lost a few drips of my fresh oil change too. Went out for quick test drive down to the corner and back.....then rode another 40 miles just to make sure !
 

Attachments

  • image.jpg
    image.jpg
    20.3 KB · Views: 0
Last edited:
Thanks for the follow-up!

Especially since I was right... :cool:

Or maybe I just happened to have the correct guess this time around.
 
You must log in or register to reply here.

Similar threads

V
Shift pedal not returning to center
Replies
4
Views
141
tom203
T
oldGSfan
A bit of help needed, GS1100E won't shift into gear and lever travel is excessive
Replies
5
Views
165
bonanzadave
bonanzadave
DimitriT
Weak idle until hot
2
Replies
31
Views
692
DimitriT
DimitriT
W
82 1100 idle issue
Replies
7
Views
174
wilsonsandy07
W
R
Need some Carb Advice
Replies
5
Views
172
RoZuki1100
R
Back
Top