• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Fork Oil #15?

Rich82GS750TZ

Rich82GS750TZ

Forum Guru
Super Site Supporter
Past Site Supporter
I know, another fork oil thread. I'm confused and probably overthinking this.:confused: My forks are apart, thoroughly cleaned, lowers polished. I got new OEM seals, cap o-rings, and copper washers for the bottom bolts and drain plugs from a local Suzuki shop. I wasn't initially going to replace the teflon rings, but think I will, for piece of mind. They look good to me, but what do I know? Anyway, my manual says to use fork oil #15. The bike and the manual are 37 years old. So what is the modern conventional wisdom on fork oil? Does #15 mean 15W? I asked the "kids" working the parts counter at the Suzuki shop about what's the modern thing to use. They said 10W fork oil, but they were out of it. Someone please set me straight.
 
10w for all-around normal riding, 15w if you're a pretty fast sport rider and willing to give up a little compliance for better control and stability when learned over.
 
Rich is the resident expert here, but I will also vouch for 10w oil in the forks. :encouragement:

.
 
RichDesmond said:
10w for all-around normal riding, 15w if you're a pretty fast sport rider and willing to give up a little compliance for better control and stability when learned over.
Click to expand...

I am firmly in that "sport rider" category, and I found that straight rate springs from Rich ( sonicsprings.com ), in an appropriate rate for my bike and weight, with 10W oil to be the best combination. You really lose a little too much compliance with 15W, I think, at least on crappy public roads.

You get better front end traction under hard braking and accelerating hard out of corners with 10W as opposed to the heavier stuff. Then again, if your local roads are perfect and/or you do track days at a track where cars haven't washboarded the pavement all to hell, you might enjoy the firmer control of 15W.

When all I could find was progressive fork springs and I needed monster preload just to get sag in the ballpark, 15W was needed to keep things under control. Once I was able to get proper springing, I was able to move to 10W and enjoy better compliance.

In the end, it's somewhat a matter of personal preference as well.
 
Last edited:
I will go with the 10W fork oil, at least to establish a base line for myself. Anything will be an improvement over the few ounces of probably 37 yr old sludge that I emptied out of the forks. I'm quite certain there wasn't enough oil in them, though I didn't measure what came out. One seal has been weeping for years, I'm just finally getting to do the full tear down and new seals. The stock springs are well within their service limits and I'm not going to change them. I want to get a good feel for what the bike should ride like with everything stock before I start to change anything up. Thanks all.
 
Rich82GS750TZ said:
The stock springs are well within their service limits and I'm not going to change them. I want to get a good feel for what the bike should ride like with everything stock before I start to change anything up. Thanks all.
Click to expand...
In my opinion, that is not a good move. :-k

Although the "service limits" (length) are apparently "good", those springs were not of sufficient strength when they were new, hence the air caps, so you could add air. Over the years, those inadequate springs have not gotten any stronger, so you will not be getting a good feel for what the ride should be like.

It is highly-recommended that, while you have everything torn apart, to just bite the bullet, get a new set of springs (cost is less than $100), then put it all together ONE TIME and enjoy what the ride is REALLY supposed to be like. :encouragement:

Go to the Sonic Springs website, use their rate calculator to determine which one might be best for you, make your purchase.

.
 
Steve, I value opinion greatly. I'm sure you're right. However, after adding up all the costs of parts I've bought and still need to buy to overhaul the caliper, MC, new brake line, fork seals and other bits, new valve cover gasket after I do the valve adjustment, upgrading the springs is not is the cards for this year's winter tear down. I'm assuming(dangerous, I know), that I would be able to swap to progressives in the future without taking the forks apart, maybe even leaving them on the bike?
 
Rich82GS750TZ said:
Steve, I value opinion greatly. I'm sure you're right. However, after adding up all the costs of parts I've bought and still need to buy to overhaul the caliper, MC, new brake line, fork seals and other bits, new valve cover gasket after I do the valve adjustment, upgrading the springs is not is the cards for this year's winter tear down. I'm assuming(dangerous, I know), that I would be able to swap to progressives in the future without taking the forks apart, maybe even leaving them on the bike?
Click to expand...
Yes, you could swap to "progressives", but for the same money, you could go to straight-rate Sonic Springs and get an even BETTER ride. (See bwringer's post #4.) The only difficulty in leaving the forks on the bike is in the accuracy of setting the oil level. The book calls for the measurement to be done with the springs removed and the tubes vertical and fully-collapsed. Easiest done when the forks are removed. It's not all that hard to remove them one at a time, which keeps the triples engaged, along with the headlight bucket.

.
 
Thanks Steve. I misunderstood the distinction between progressive vs. straight rate. I clearly have a lot to learn. Going to leave as is for now.
 
Tom R said:
A little insight on different fork oils.

http://www.peterverdone.com/wiki/index.php?title=Suspension_Fluid
Click to expand...
If you look at that long list, you will see some interesting stuff. Some 5w oils are thicker than other 7w oils, which can make tuning "interesting". Best suggestion would be to find a brand that is readily available in your area or from your favorite online store. Stick with that brand if you decide to to any viscosity changes.

.
 
Steve said:
If you look at that long list, you will see some interesting stuff. Some 5w oils are thicker than other 7w oils, which can make tuning "interesting". Best suggestion would be to find a brand that is readily available in your area or from your favorite online store. Stick with that brand if you decide to to any viscosity changes.

.
Click to expand...

Will do Steve, thanks. And thanks TomR for the great article. You guys are the best.
 
You must log in or register to reply here.

Similar threads

crazyramen
'79 750 Fork Oil Level
Replies
4
Views
110
crazyramen
crazyramen
K
Looking for fork oil advice
Replies
5
Views
150
salty_monk
salty_monk
D
Squeaky front forks
Replies
13
Views
231
salty_monk
salty_monk
oldGSfan
I am looking for some help with my '83 GS1100E fork setup using emulators
Replies
10
Views
251
diptenkrom
D
H
Fork Seal Snap Ring
Replies
3
Views
86
hookemdevils22
H
Back
Top