• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

installing carbs gs1000

  • Thread starter Thread starter george g
  • Start date Start date
G

george g

Guest
1980 gs1000. Trying to get carbs to go into rubber manifolds on head. Can't seem to force them in. Is there a proceedure that make this happen any easier?
Thanks!
george
 
Are your intake boots new or old? sometimes they can be a bit of a brute, a bit of lubricant on the boots can help, it's just a bit of force and push sometimes.
 
A bit of lubrication helps -- a few drops of oil wiped onto each boot.

Also, make sure they are installed correctly. Dunno about your bike, but on some bikes there are right and left boots and they must be installed the right way up and in the correct locations or things will never line up.

If the boots are old and hardened, the correct procedure is to remove one's Visa card from the dusty recesses of one's wallet with the index finger and thumb and order up new ones.
 
Cargo straps and something to put behind the carbs to put pressure to the boots evenly, like a length of wood.
 
Thanks so far everyone. I believe that my "left" and "right" manifolds are correct, L and R facing up. There is one new manifold and three old. They all felt about the same softness. I have applied lube and my next thought was to fab some way to assist with leverage as has been suggested. This has helped me to realize that they are apparently often difficult and some futher force may be required. I 'll post again.
Thanks!
george
 
Well it was a forceful event but there on there. Used a 2x4 in front and one in back with with some 24" wood clamps to squeeze em in. they seem to have survived.
Thanks for the help.
g
 
WOW :eek:, that's crazy, I've never had to even come close to doing that kind of surgery to get carbs in, too bad you didn't have a picture of that setup, would have liked to have seen that. Anyways, glad you got them on, bet you're not looking forward to that again.
 
Squeeze the front brake and hold it back with a bungee so the bike doesnt roll off the stand.

Next just a little WATER will lube them. I dont use oil for the fact that it doesnt dry out and allow the rubber to seal against the throats. Water WILL dry out and let DRY rubber touch the throats.

Third..put down the rear foot pegs and get you leg in front of them for added body leverage.

Roll thecrabs in starting them into the BOTTOMS of the carb holders. Thius allows you to look down and use a flat tip screwdriver to help coax the airbox boots past the intake sides of the carbs. Have the clamps off the airbox boots nd back against the casing to not bend them up. once all is in place, slip the clamps up into location and tighten them up.
 
chuck hahn said:
Next just a little WATER will lube them. I dont use oil for the fact that it doesnt dry out and allow the rubber to seal against the throats. Water WILL dry out and let DRY rubber touch the throats.
Click to expand...

Why not use grease?

Don't you always lube/grease your o-rings? Why would this be any different?

With some grease on mine, they slid right in, and I am unaware of any vacuum leaks.
 
I have replaced lots of them with no problems. On one of my 1000Gs, they are always a bitch to do. I think that they weren't made right or something. One thing though, once you have them in, they are easier the next time.

Some times they are more difficult than they are at other times.
 
chuck hahn said:
Roll thecrabs in starting them into the BOTTOMS of the carb holders. Thius allows you to look down and use a flat tip screwdriver to help coax the airbox boots past the intake sides of the carbs.
Click to expand...

Since I just pulled out my carbs (with difficulty) this thread is timely for me. But my go-to tool for something like this is a Craftsman Cotter Pin Puller $8 - or a Harbor Freight Radiator Hose Pick $3. I prefer the Craftsman tool; I use it all the time to get hoses on and off. Due to the bend it is much easier to use than a screwdriver, particularly in places with little clearance.
 
You must log in or register to reply here.
Back
Top