• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Looking for brake pad opinions...

  • Thread starter Thread starter Guest
  • Start date Start date
I always have backup front and rear pads ready to go. Also purchased from Fleabay.
 
Thank you all for the discussion & tips regarding brakes and such...

As with all things, I can see that there's those who get replacement parts based on the best "engineered" or "performance" aspect of the part, and then there are those who use price and economic value as a guide.

I would say I'm somewhere in the middle, with a noticable lean towards the cheap side!

Since I'm not a super aggressive rider, nor do I put more than 5K per season on my bike, I will most likely go with inexpensive pads like the SOK from e-bay.

Appreciate the feedback,

Mike
 
My '79 550 front brake judders when it's applied. The bike has less than 1000 miles from new and the original owner must not have ever used the front brake since the rotor looks like new.

I'm torn on whether or not I should replace the pads or try to burnish them in some more before spending money.

Ebay offers all kinds of old brake pads for this model brake caliper - with the round pad: Tuff Stop, K&N, and a couple of generics are available for about $10 or even less. Using Grandpa's theory, all these are the same. EBC's are a little more but are a known commodity so I'm leaning that way.

http://cgi.ebay.com/ebaymotors/LQQK...018QQitemZ280165211028QQrdZ1QQsspagenameZWDVW

http://cgi.ebay.com/ebaymotors/SUZU...002QQitemZ120130578385QQrdZ1QQsspagenameZWD1V

http://cgi.ebay.com/ebaymotors/New-...007QQitemZ170134143203QQrdZ1QQsspagenameZWD1V
 
Last edited:
Pads

Pads

I've only used Vesrah and EBC but thought they were very similar and not a danger to my rotors. I can't tell the difference in performance but I'm sure people with more experience might. I never try to save money on either pads or tires because both are really important....and don't need replacement all that often, anyway.:)
 
Nessism said:
My '79 550 front brake judders when it's applied. The bike has less than 1000 miles from new and the original owner must not have ever used the front brake since the rotor looks like new.

I'm torn on whether or not I should replace the pads or try to burnish them in some more before spending money.

Do your brakes judder under hard or moderate braking. If light to moderate, your wheel bearings may be shot causing the wheel and rotor to oscillate between the pads. A warped rotor will also causer this to happen. If your rotor surfaces have been re-machined and the rotor wasn't aligned correctly, this will cause it to runout and cause the brakes to judder.
If the judder occurs under hard braking, you may need to service/replace your front shocks.
Click to expand...
 
49er said:
Do your brakes judder under hard or moderate braking. If light to moderate, your wheel bearings may be shot causing the wheel and rotor to oscillate between the pads. A warped rotor will also causer this to happen. If your rotor surfaces have been re-machined and the rotor wasn't aligned correctly, this will cause it to runout and cause the brakes to judder.
If the judder occurs under hard braking, you may need to service/replace your front shocks.
Click to expand...


This bike has less than 1000 miles since new. The bearings, rotor (looks brand new ? previous owner obviously only used the rear brake), and front forks are in as-new condition.

I'm almost certain the problem relates to the fact that the brakes were never bed-in properly when the bike was new and now the pads are 28 years old. These are the round pads that Suzuki stopped using in 1979.

Think I'm going to tear-down the caliper and make sure it?s clean on the inside, and take some sandpaper and scuff-in the pads to remove the surface layer which has been exposed to the air all these years. If the brakes don?t settle down after that, I?ll order some new pads from ebay.
 
Take the sharp edge or corner off them with a file too & put a bit of copper grease or similar on the back.

Dan :)
 
salty_monk said:
Take the sharp edge or corner off them with a file too & put a bit of copper grease or similar on the back.

Dan :)
Click to expand...

I DO NOT recommend putting any grease at all, of any type, anywhere near brake components, for shuddering clean the brakes down thoroughly, rotors pads calipers and all, then apply a very light smear of silastis to the rear of the pad, let it set then re-fit the pads.

Dink
 
Dink said:
I DO NOT recommend putting any grease at all, of any type, anywhere near brake components, for shuddering clean the brakes down thoroughly, rotors pads calipers and all, then apply a very light smear of silastis to the rear of the pad, let it set then re-fit the pads.

Dink
Click to expand...

Silicone grease is very common to use on brake caliper parts, such as sliding pins and parts where there is relative motion between the parts. PBC grease with lead is also common. You just don't want to use a whole lot since the grease can run when the parts get hot. If I'm not mistaken the manual even calls for grease on these parts.
 
Before you spend any money.. (And believe me, I'm cheap too..) you might want to check just where your brakes stand.

if you can get your mits on a micrometer, measure the thickness of your rotor..

If you are well with in tolerance, say.. no more that a 60% wear, then you can probably go with cheaper pads that may contain harsh abrasives. other wise, i would advise.. if you really need to pinch pennies.. going with CHEAP PADS THAT DO NOT HAVE HARSH ABRASIVES.

I have NO idea how a simple question about the make up of a particular pad turned into another argument over safety vs money.. is it worth it.. how much to spend and which brands are the best.. and grandpa finding more rocks to throw at eiger and willing targets.

MY answer is quite simple. that particular pad you asked about, appears to have more abrasives in it than would normally be required. That is all. I really don't know how it performs. may be you can get another pad from the same company, for the same price, with less abrasive.


By the way.. you guys want to know cheap??

MY pads.. are SALVAGED!! I didn't pay a dime. I took pads that were completely soft and moister saturated, and baked them!.. in a house hold stove!..(What a smell that was) and then i conducted hardness tests with a center punch and a welder's hammer. THAT IS CHEAP people. and ya know what.. they work great.. my bike is more than capable of doing endo's.
on that.. i don't recommend this route. I have access to information through my university, that most people dont.

oh, and rockford.. I use Chenshin tires.. cause they are cheap too.
I will let you guys guess what kind of oil i use..
funny enough.. i put in premium or plus gas...
 
Last edited:
You must log in or register to reply here.
Back
Top