• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Those little rubber thingies

  • Thread starter Thread starter drhach
  • Start date Start date
D

drhach

Guest
Hey everyone, I just got my 1978 GS1000 running and I noticed that three of the four rubber plugs that go between the valve cover and the head are leaking like sieves. I see that the PO put some orange silicone on them. Is this a common leak? I ordered some new ones. Will they leak too, or am I just dealing with old rubber components. Is there a trick to this? I'm not against silicone, but I'm not sure it is a substitute for maintenance. I want to put my shiny chrome endcaps on, but I can't do it until I'm sure these things don't leak. Thanks.
 
Probably time for new ones. Bikebandit sells them as do lots of places. I think Z1enterprises actually has them for cheaper.

Put 'em on with a bit of RTV for a good seal.
 
t3rmin nailed it. Buy new and it should stop leaking. Personally, I use teflon tape and not RTV but both will work.

Hap
 
Steve said:
Actually, just a tiny little bit of RTV. The rubber is doing the sealing, the RTV just holds them in place while you tighten the screws. 8-[


.
Click to expand...

I agree that you only want a thin film, but I'd contend the RTV is there to assist with sealing. I put it on the top and arc of the half-moons (ie: all the way around). Also the RTV helps to cement the things in there so they don't pop out on the road (not uncommon).
 
The rubber gets hard with heat from the engine and then starts to leak. New ones will be slightly bigger and crush down when you tighten the rocker box up. I personally don't use any sealant at all on these rubbers.

Suzuki mad
 
I didn't use any sealant on mine except for one... the old one had sealant on it & guess what... the new one leaked too in the same place!!

I used a smear of silicon.

Flanges on the inside for me too.

Dan :)
 
Suzuki mad said:
New ones will be slightly bigger and crush down when you tighten the rocker box up. I personally don't use any sealant at all on these rubbers.
Suzuki mad
Click to expand...
I do it this way as well. No problems.

My Suzuki shop manual calls for a bunch of sealants and thread loc on a lot of the assembled parts, but nothing on these side plugs. (I leave the thread lockers and sealants off of most of the parts that call for it too, but that's another problem :) )
 
New ones are on order. Thanks for the replies. I was a little crusty before I turned 30 too.
 
You must log in or register to reply here.
Back
Top