• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

1979 GS850G Clutch just isnt right????

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
I recently posted a message regarding proper adjustment of my new clutch cable on my 79 GS850G. I just cant seem to get it right. On the first ride the clutch was sliping real bad when I would give it about half throttle at cruezing speed. I got to my destination and losened it up just a little bit down on the case adjustment and now it wants to jump when in gear and I cant take it out of gear at all when the motor is runing. Its idling at about 1500 like the book says. The carbs need to be synced but this was all the same before my old cable snapped witch worked great. Any suggestionjs?
 
Well, it sounds like you just need to move the adjustment to somewhere in the middle. If the clutch was operating properly before the cable snapped the odds are pretty good the problem is with the cable and not the clutch.

When properly adjusted there should be a short but noticeable amount of play between the time you squeeze and when you feel the resistance of the clutch pull. The exact amount of play is subject to preference. I like more play than most do, Just so long as you can fully disengage the engine and can idle in gear with the clutch pulled. You should at least be able to insert a toothpick in the clutch lever hinge opening without engaging the clutch.
 
This is just to weird as there is no reason why it should not work. I wish some of you "bike smart" guys lived nearby so you could see how weird it is. I got the clutch working fairly well but it still takes quite a bit of ankle strenth to get it in nutral while at a stop. Here is a new problem. It darn near takes 2 hands to pull the clutch lever in. Its so hard I am scared to stray to far from home in fears of snapping my new cable.
 
The most likely cause of the new, and very hard, lever pressure would be altering the original routing of the cable


It appears you have a crimp or kink in it. This will cause the inner cable to bind, making it hard to pull, and also slow to release.
 
BINGO WE HAVE A WINNER. After my post I went out to tincker with and put some polish on the bike. I went through my book and tryed once agan to adjust the cable and everything acordingly and found a kink while doing so. Right at the end of the cable on the clutch side there is a chrome piece that kinda fits inside the adjusment nut. Well as fait would have it that chrome piece was pulled out and gave the cable about a 50-60 degree angle. I poped it back in and readjusted but 330am was to early to fire the bike up and test it so in ohhh 4 hours or so I plan on taking it out and hoping everything is good now. Thanks for the great help I do much apreciate it
 
argonsagas said:
The most likely cause of the new, and very hard, lever pressure would be altering the original routing of the cable


It appears you have a crimp or kink in it. This will cause the inner cable to bind, making it hard to pull, and also slow to release.
Click to expand...

I'd second Ron's bet, if you can't get it right, Carmichael's not too far from you. When installing the cable, think nice easy loop, don't tie-wrap it to anything either :lol:
 
After putting Dyna coils on my bike, space for wiring and cables was tighter under the tank. The clutch cable was getting trapped when I turned the handlebars, which caused it to bind.

I ran the clutch cable through a loose-fitting piece of the plastic corrugated stuff you use to cover wire looms. That allows it to "float" and move back and forth just enough.
 
You must log in or register to reply here.

Similar threads

T
GS850G won't go into gear from idle
Replies
5
Views
97
dandypop
dandypop
D
Clutch
Replies
8
Views
178
tom203
T
D
4th clutch cable in 10 months
Replies
3
Views
75
Nessism
Nessism
W
Broken clutch cable on a group ride!
2
Replies
24
Views
245
argonsagas
argonsagas
R
My 2000 Kawa ZRX, 2 very strange problems on 1 short ride.
Replies
7
Views
87
rphillips
R
Back
Top