• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Bad Dyna S ?

  • Thread starter Thread starter SAN
  • Start date Start date
S

SAN

Guest
Boy's & girl's, I am puzzeld. I have A 81 550T 10k stage III dynoJet,K&N pods,coil mod,Honda rectifire upgrade, MAC Mod baffle, DYNA S, FZ1 coils. Ran like this all last year. left house on bike Today W/ligt switch off DUH! 5 mile's on It, Did another 5miles stoped at light, Took off bike was down on power and cotinued to be running on two cyl. Got 1/2 mile to my brothers house bike died in drive way. Turned over but no Vroom Vroom! Checked fuse box first, all ok. checked fuel OK. checked plug fire Nothing. 2&3 cyl plug caps hot hot hot! Checked fuse for the coil mod Relay, TOAST! Changed fuse,Unplugged white coil wire on cyl 1&4 too test ohm's. Didnt find the multi tester. turned key on too check fire, noting! relay fuse still ok. Lost ign fuse, toast. changed. I then noticed the coil i was checking for fire was unplugged? DUMMY! plugged it Turned key hit button not turnning over?Main fuse blown. looked at my grounds. suspected bad rectifire ground. wire was streched,tight. unhooked REC ground to frame. loose inside terminal conector. Crimped conector, felt some compression on wire.hooked it back to frame. changed fuse. turned key. fired up on two cyl only. cheked plugs 2&3 wet. changed.started again, still two cyl only. Checked volts to coils 12.2v checked ohms to #2&3 8ohm 1&4 3ohm changed coil W/spare. no fire. on 2&3 only 1&4 running .I wired coil Backward's. fixed another Frakk up. Started bike, still runing on 1&4 only. ohms on 2&3 was 3. 1&4 now 8ohms but still runs on 1&4 2&3 dead still. Had to Quit My Back is Wack! Suspect Dyna S is gone on one side took a quick look unhooked BAT. took each side off (after I Marked placment) too look for something? AS far as I got. Can Anyone help, It would be greatly Welcomed. Will test dyna for correct readings on dyna web site. Thanks too anyone who read this far! Shawn.:confused:
 
Hot plug caps indicate a high contact resistance. Mine were breaking down, and toasted a coil. I would replace them before they cause more problems.
 
Bad dtna

Bad dtna

Knowone ever screwed up like me. I meen Bad ground light off,cause a voltage spike? something,It cant bee
worse than me, Can PM me. SAN:confused:
 
Do you know the resistance of the FZ1 coils stock? The dyna S is for 3.0 ohm coils.
 
dyna

dyna

was told 3ohm by owner? checked out w/meter. still have stock coils but tried them, seems damage already done. im heading too the lift now. W/luck:rolleyes:. san
 
Back
Top