• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

can a piston be saved?

  • Thread starter Thread starter scottsgs
  • Start date Start date
S

scottsgs

Guest
Hi all,

I got the head and cylinders off the bike. However I noticed a nick or gouge on the top edge. Is this piston ruined, or can it be saved? Also, if it is gone, can I replace just that 1 or do I have to replace all 4?

Thanks,

Scott
 
So long as it doesn't interfere with the rings, I don't see why it would be a problem.
 
Photo would help but it doesn't sound like a problem. Just make sure the ring groove is not crushed down or otherwise compromised in that area.
 
my only concern would be the possibility of it being a potential detonation site. Be absolutely sure that you aren't running lean on that cylinder.
 
I agree with all said above, as long as it does not extend down to the fist ring groove, you should be fine.
What you can do to prevent detonation, and stress fractures, is to dress out any sharp burrs and edges with a fine needle file, thus releiving the stress and preventing a point where a stess fracture can start.
We do this with propellors that have picked up nicks and chips due to stones or other objects, it works great.
By dressing out all the sharp bits, you also remove any triggers for detonation.
In short....no need to junk it.
Hope that helps.
 
Like others have said as long as the rings are not compromised you should be fine. Use a fine file or even sandpaper to get rid of any high spots. I have had to do this kind of thing a few times and never had an issue.

It's more important to be checking things like the wear on the bore/pistons, and the ring end gap.
 
cleonard said:
Like others have said as long as the rings are not compromised you should be fine. Use a fine file or even sandpaper to get rid of any high spots. I have had to do this kind of thing a few times and never had an issue.

It's more important to be checking things like the wear on the bore/pistons, and the ring end gap.
Click to expand...


Agree.

Measure the cylinders for bore roundness and taper. If the service limit is reached, time for a bore job. Otherwise, new rings and a hone job are always a good idea if the engine has a fair bit of mileage - say, 20k and above.
 
Hey, now, don't let them kid you. You can save any piston for as long as you want. :shock:
Here is one that I took out of my car back in 1975.
IMG_2962.jpg


Now back to your bike...lots of good advice given above. Remove any high or sharp edges, make sure there are no gouges in the cylinder wall. A picture would help, but based on your description, there should not be a problem. If you feel better about replacing it, you should only need the one, but it would be better to measure the cylinders to make sure they are still in good shape and not tapered due to wear. If the cylinders are looking worn, it would be better to bore them and order 4 new pistons to match.


.
 
Steve said:
If you feel better about replacing it, you should only need the one
Click to expand...
Yeah - cylinders don't talk to each other - each one is an individual and if it's OK, it's OK.

Replacing in sets is something dealers tell you to do - like replacing brake cylinders in sets - the damn things are designed to adjust for differences FFS. It's just a stealer money-maker.
 
Oh, and exactly what sort of vehicle are we talking about here?

It doesn't make much difference for this particular topic unless you're trying to set a land speed record. But it's important most of the time.

All good advice so far!
 
You must log in or register to reply here.
Back
Top