what did you wrench on today??

[Guest]

Today I worked on the side covers on my new (to me) Honda CL 160. There are some holes where the metal has rusted...looks to me like
moisture collected inside the left side cover while leaning on the side stand. No big deal. Using a bit of fiberglass and some resin. After that I
hope to do some spot putty on some imperfections on the outside of the covers, then match the silver paint at a local paint shop here.
I'm in Barrie, Ontario.

 

[Guest]

Also, I'm a newbie for the 2nd time. I found this forum back in July 2015, wrote a post about my GS1100. I totally forgot about joining,
and, well, apologies to "Redman"..."dorkburger"..."Highway_Glider"...."chuck hahn"...."GS1150Pilot"..."gsrick"...and any others
who had replied asking for photos and where I live etc. My bad. Anyway, posting a couple photos here now if I'm able.
-nesster

 

[steve murdoch]

Daytona? Wouldn't mind being some place warm this morning after another winter wallop.

CL160 with a side stand? Don't see many with that option.

 

[Guest]

Ya that photo from New Smyrna Beach in 2008...my first trip to Bike Week. That was the year I retired, threw the bike in bed of my pick-up and drove strainght through from north of Toronto to New Smyrna campground...23 hours. I have some better photos of the bike so will post as soon as I find 'em. You know, I'm not sure this CL 160 does have a side stand - I just bought it and it's partially assembled. Ijust figured if one side-cover had perforations in the bottom it was probably moisture/rain collecting on the "low side. It did come with a center stand! Hope to have it running this spring or summer.

 

[Guest]

Here's not a bad shot of the '81 GS 1100E. I was on the way home from Bruce Peninsula (north of Owen Sound, Ontario) to my home in Barrie. It was one of those rides when you're trying to outrace a storm. I'm pretty sure anyone who has done extended rides will know exactly what I mean. I was successful on this day - a totally dry ride home!

 

[Guest]

Got my oil changed on the 750, fresh plugs next. Gotta get it out and ride it more, it's been nelgected some since the Spyder came on the scene.

 

[fastbysuzuki]

Had an hour or so in the garage putting the rf900rw exhaust back on after rubbing down part of the down pipes and giving them 3 coats of flame proof vht primer paint followed by 2 coats of flame proof vht finish coat.
I say part of the down pipes as mr Suzuki in his wisdom made the short headers in stainless followed by longer headers in mild steel followed by the rear in stainless why!!!
I just hope the expense and effort pays off to cure the paint the directions say run at idle for 20 mins followed by cooling of for 20 mins followed by a further 20 mins at idle then let to cool off. Alternatively you can bake in an oven if you had one big enough or wanted to live if her indoors caught you.
Due to various parts being off the bike the curing will have to wait for a month or two.
if anyone has used this process please let me know your experience's.
I am a time served mechanical engineer and I checked the workshop manual for the torque setting for the manifold fasteners 23 nm got to admit I was getting nervy tightening those fasteners it seemed very tight given it's an alloy cylinder head.

 

[Gorminrider]

I worked on being a better person.

and, I replaced all the sparkplug caps on the GS650. The old ones are just too funky and one of the ceramic resistors is burned. The new NGK are 5k resistance vs the OEM 10k but that is not a problem. I'll try resistor plugs first with the new and non-resistor if the bike seems unhappy.

 

[Guest]

fastbysuzuki I did my brakes a decade ago with VHT paint. Not wanting to get caught with them in the oven I hung them from the top rack of the barbeque and set it to the correct temperature with the lid slightly ajar so it would not overheat. I cleaned the barbeque first before doing it so as not to get grease on them. Would I do it again? Likely not as powdercoated finish kits are now available. Someone from this forum chimed in and said that if you leave them for a month they would cure on their own. They lasted about 7 years but winter storage in a cold shed one year at -30 is likely what did the finish in. They started to flake off the next riding season.

 

[Carter Turk]

Changed oil/filter cold on the 04 track bike with some Actevo 10/40. Hadn't been started since 9/20/20, coincidentally the day of my big wreck in 1988.

It protested a bit on initial start up, not holding idle, fuel pump cycling, but eventually settled into a nice steady idle. Took a little blip around the block.

Realized I lost the Stomp Grip on the tank from the right side, not sure when that fell off, sometime last year apparently.
20210218_165639 by Carter Turk, on Flickr

 

[free99]

Scuffed up the clutch plates and friction disks with red scotch brite, cleaned with alcohol, new OEM springs. Bike feels like it got +15HP, I expect oil temps will go down too.
Also replaced what I hope is the source of a persistent oil leak, the clutch pin seal.
Bike's running pretty nicely

 

[Baatfam]

Got her out, dusted her off, checked her fluids and tires, and fired her up......All ready to go...

 

[storm 64]

Lookin' good Bob! I see the top down on the convertible
Another thing I'd love about Tennessee. Spring time comes so much sooner than in N.E.Ohio.

 

[oldGSfan]

Nice GS, and looks like Sam Adams has paid a visit

Got her out, dusted her off, checked her fluids and tires, and fired her up......All ready to go...

 

[Baatfam]

Lookin' good Bob! I see the top down on the convertible
Another thing I'd love about Tennessee. Spring time comes so much sooner than in N.E.Ohio.

Been a late start this year, but we are getting there.
Another nice thing is pure gasoline. She fired up and ran great after sitting most of last year.

Nice GS, and looks like Sam Adams has paid a visit

Haha....10 years or so ago, the wife and I tried home brewing. Probably did 12-15 batches....
That's what's left. Every so often, I chill a couple down, drink them, and remember why I get my beer at the store.

 

[allojohn]

Nice GS, and looks like Sam Adams has paid a visit

LOL, I love (virtually) nosing around someone else's garage... there's always an interesting item or two.. with a story.

 

[GS1150Pilot]

I learned a lesson. The Sporty threw a rod. Found out that the heads had been skimmed prior to my owning it, so, while initially, the pistons did not touch the heads or valves, the possibly insane compression ratio after I installed the 1200 kit exacerbated a rod going out, such that the rear piston eventually began to smack things it shouldn't. I had no idea that the motor had ever been apart, since I bought the bike with 10K on the clock.

Long story short, I ordered a very low mile 1200 motor which arrived yesterday.

 

[RustyTank]

Long story short, I ordered a very low mile 1200 motor which arrived yesterday.

Let me know if I'm outta line askin this but, what did sometin like that set ya back?

 

[GS1150Pilot]

Let me know if I'm outta line askin this but, what did sometin like that set ya back?

The motor was $2000 shipped.

 

[Sandy]

Pretty much got the GS put back together from a winter of deep cleaning, valve clearance check, a bit of polishing covers and a carb swap. It fired right up and settled into a good idle and I was surprising close with my preset adjustments and bench sync. A quick session with the carb sticks and a fiddle with the air screws and all is well. Nice smooth 1,000 RPM idle. Woohoo.



2021-03-10_02-59-18 by soates50, on Flickr