82 850GL Resto...here we go

[simonw]

I noticed you are running pods on your 850 .. any chance you know what jetting your using in the carbs?

Also what was the result of your rear caliper leak? i think mine is doing the same

 

[growler]

what a great mini-novel to read while having a bit of insomnia.

how did you polish your carb tops and bowls? i've been using a dremel with cutting/polishing compound and they don't look as nice. did you use anything specific?

 

[GateKeeper]

what a great mini-novel to read while having a bit of insomnia.

how did you polish your carb tops and bowls? i've been using a dremel with cutting/polishing compound and they don't look as nice. did you use anything specific?

have a look here

http://www.thegsresources.com/_forum/showthread.php?t=195934

.

 

[growler]

weird. i'm using the same kind of process, same compounds....

i'm keep working at it.

 

[Good Times]

I noticed you are running pods on your 850 .. any chance you know what jetting your using in the carbs?

Also what was the result of your rear caliper leak? i think mine is doing the same

Simon, sorry I missed this post to my thread. I know I'm a little late, BUT:

I have a Dynojet stage 3 kit installed in my carbs. Works like a charm. Smooth acceleration all the way through to red line.

My rear caliper leak was the result of not getting the piston seal groove clean enough. It has to be spotless.

what a great mini-novel to read while having a bit of insomnia.

how did you polish your carb tops and bowls? i've been using a dremel with cutting/polishing compound and they don't look as nice. did you use anything specific?

Thanks Growler. The polishing disease has hit many of us. It's a disorder really. It looks like GK took care of you, but here's my process:

sandpaper:
400-800-1000-2000

Polishing compounds:
Black - brown - white - green (I use the yellow polishing wheel from Lowe's on my bench grinder)

You'll be shaving in it after that process.

By the way, I got her out to day after our crazy winter and took her for a spin. She started right up and after a little smoke, idled right down to where she should be and ran smooth the whole ride.

Love that bike!

 

[growler]

i'm jealous. we're getting our last hit (hopefully) of the POLAR VORTEX here in wisconsin. can't wait to ride!

Thanks Growler. The polishing disease has hit many of us. It's a disorder really. It looks like GK took care of you, but here's my process:

sandpaper:
400-800-1000-2000

Polishing compounds:
Black - brown - white - green (I use the yellow polishing wheel from Lowe's on my bench grinder)

You'll be shaving in it after that process.

By the way, I got her out to day after our crazy winter and took her for a spin. She started right up and after a little smoke, idled right down to where she should be and ran smooth the whole ride.

Love that bike!

 

[William Groebe]

Good Times.

What a truly inspirational journey you've shared with everyone here. You've done an amazing job cleaning up your GS to original (if not better) quality. I'll definitely be referring to this thread when I pull apart my 82 GS650GL.

Did you ever put the badges on? I'd love to see the final version.

Keep on wrenching.

 

[Good Times]

Hey Will, I still haven't put the badges on. I started back to school and the paint job took a back seat. I still have the badges and will put them on after paint. I will actually be taking it to the shop (GASP!) for two time-serts (one exhaust bolt and the oil drain). After that I will be riding it in the spring. Good luck with the 650!

 

[Guest]

Hey GT, I'm a little late to the party, but I have to say 'great job' on your L.

Mine will never look that good as I plan to ride it and do little bits at a time.

When I first read about your screen I thought 'Oh dear, that's going to look really... Wait a minute, actually that looks really good.'

Love all the new parts and mods that you've fitted. I noticed that in your videos you sound like a cheery chap, obviously you haven't kept a record of what this has cost so far.

Do these things ever get truly finished?

Enjoy the ride.

 

[Good Times]

Cyrano, thanks!

One time during the resto I made a list of parts I needed and added up the cost. I don't suggest doing that. I almost walked away from it. So, no I didn't keep a running total. I guestimate that I have right around $3500 in the whole thing. That includes the cost of the bike, new tools, powdercoat, and parts. I probably could have done it a little chaper, but I didn't get into it to save money. I had a really good time working on it and will continue to tinker with it until I get it just right. Of course I would have been dead in the water a few times had it not been for the good people on this site.

 

[Good Times]

I took my bike to the shop last week. That's right, THE SHOP. Cue the scary music. I had a stripped exhaust bolt and the oil drain plug bolt was just about to go. Instead of Helicoils I wanted Time Serts. The tools and time serts were more expensive than letting the shop do the job for me. I also didn't like the thought of accidentally drilling into the oil passage behind the exhaust bolt. :shame: Two time serts, crush washer and a new valve stem on the front tire.

Picked her up yesterday and I am set. Looking forward to another season on the GS.

 

[Guest]

I had a stripped exhaust bolt ...

I know the feeling. I found three yesterday (the first three from the LHS). Still debating which way to tackle this. (If only I had a MIG welder to hand)

 

[Good Times]

You can go helicoil, but they eventually pull out from what I understand. The Time Sert is the best fix I know of. Had I not needed to have the oil drain done, I might have gone with a helicoil and then just replaced it if it eventually came out.

 

[Good Times]

Speedo Repair

Speedo Repair

I have gone through two speedo cables and finally figured out that it was the old hard grease in the gauge that was dragging and breaking the cables. So to remedy that I got into the speedometer, cleaned it up and put it back together.



I started with a nail and hammer, methodically tapping around the bezel of the lens to bend the lip up.


After removing the bezel I cleaned up the mechanism with some carb cleaner followed up by some Balistol:




Then I reversed the process by using the head of the nail to tap the lip of the bezel back down:


It takes more time, but I prefer this process to cutting the plastic cup. If you take your time you can get the bezel looking almost as good as stock. Once you put the sleeve back on the gauge you can't tell the bezel was touched.

The gauge is turning freely now and a new cable is on order.

 

[GateKeeper]

Tip of the day.....next time you can use a paint lid tool to pry the metal back...so I have heard...

 

[Good Times]

Tip of the day.....next time you can use a paint lid tool to pry the metal back...so I have heard...

DOHP!!!! What a great idea. That would have been so much easier once you got it started. Thanks GK

 

[Good Times]

I thought my speedometer cable was broken. That was the problem in the past. Ordered a new one. Got it in the mail. Went to put it on today after my Speedometer refresh as described above. When I removed the old cable I thought I would remove the inner cable to see where it had broken. I was surprised to see that it was actually intact.

I removed the front wheel and speedo gear box only to find that the gear box is completely frozen. Thus the problem. I removed the snap ring. That and the washer are the only part that I could remove. So now I'm looking at options.

Thoughts? Buy a new one? Anyone here have an extra?

 

[Guest]

Just stopping in here. I've got my 1100GLZ slightly apart after some severe neglect in the hopes of getting it running for the tail end of this riding season. Naturally (via wiring harness search terms), ended up on this thread. After reading the whole thread (I have a lurking sickness similar to your polishing sickness) I only have a couple things to say:
- Sorry to disappoint with a bump that doesn't help with your speedo gear box problem (hopefully sorted by now?)
- Great job with this restoration! You've inspired me to tear mine apart this winter and do the same. Except I can't part with the pretty red of my tank and original side-covers.

Good work! Hopefully an update is in short order.

 

[Good Times]

Just stopping in here. I've got my 1100GLZ slightly apart after some severe neglect in the hopes of getting it running for the tail end of this riding season. Naturally (via wiring harness search terms), ended up on this thread. After reading the whole thread (I have a lurking sickness similar to your polishing sickness) I only have a couple things to say:
- Sorry to disappoint with a bump that doesn't help with your speedo gear box problem (hopefully sorted by now?)
- Great job with this restoration! You've inspired me to tear mine apart this winter and do the same. Except I can't part with the pretty red of my tank and original side-covers.

Good work! Hopefully an update is in short order.

Thanks for the bump Evark! Tear into it and enjoy the process. I hope it goes well.

I am going to replace the speedo gearbox, just haven't done so yet. Actually, the bike (along with my other hobbies) has been sitting for most of the Summer. I am finishing up a degree tha requires all of my free time this Summer/Fall. Priorities! I can't wait to get back to my garage though.

 

[dorkburger]

Dont know if your speedo is sorted yet (I see its an old post). I had similar problems.
http://www.thegsresources.com/_foru...38-1150-speedo-drive-quick-rebuild&highlight=